MA0602-EA
Operation Guide 4725
Getting AcquaintedTo set the date
1. With the crown in the normal position, rotate it until the mode hand is pointed at
Congratulations upon your selection of this CASIO watch. To get the most out of yourTME (Timekeeping Mode).
purchase, be sure to read this manual carefully.2. Pull the crown out to the first click. This will cause the second hand to move the
" For watch with the elapsed time bezelcurrently selected month setting and stop.
10Rotate the elapsed time bezel to align the mark with3. If you want to change the month setting, press B.
50the minute hand. After certain amount of time elapsed,December
20read the graduation on the elapsed time bezel which theNovember January
40
30minute hand points to. The elapsed time is indicated.
October
Elapsed time bezelFebruary
September March
April
August
"Some water resistant models are equipped with a
screw lock crown.July May
"With such models, you must unscrew the crown in theJune
direction noted in the illustration to loosen it before
4. Rotate the crown to set the day.
you can pull it out. Do not pull too forcibly on such
" Rotating the crown one turn towards you until you feel a click will advance the
crowns.current setting one day.
"Also note that such watches are not water resistant
" Rotating the crown two or more turns will scroll the day setting at high speed. To
while their crowns are loosened. Be sure to screw the
stop high-speed date scrolling, rotate the crown towards you or away from you one
crowns back in as far as they will go after making anyturn. If you do not stop high-speed date scrolling, it will stop automatically after a 31-
setting.
day cycle.
" Note that the day setting can be scrolled forward only. It cannot be scrolled back.
5. Push the crown back in to the normal position to restart timekeeping.
About This Manual
" Button operations are indicated using the letters shown
in the illustration.Stopwatch
" Each section of this manual provides you with theThe stopwatch lets you measure elapsed time up to 59 minutes, 59.95 seconds.
information you need to perform operations in each
mode." Stopwatch minute hand
" Stopwatch 1/20 second hand
Stopwatch second hand
Crown (Normal position)
General Guide
Crown Positions
Mode hand
First click
To measure elapsed time
1. With the crown in the normal position, rotate it until the mode hand is pointed at
CHR (Stopwatch Mode).
Second click 2. Press A to start the stopwatch.
3. Press A to stop the stopwatch.
" To view the 1/20-second count, hold down B. This will cause the stopwatch minute
Crown (Normal position) hand to move to the applicable 1/20-second value. After you are finished viewing the
1/20-second count, release B.
Selecting a Mode" You can resume the elapsed measurement operation from the point it was stopped
With the crown in the normal position, rotate it to select the mode you want.in step 3 by pressing A again.
The current mode is indicated by the mode hand.4. To clear the stopwatch, stop elapsed time measurement and then hold down A.
Dual Time
The Dual Time Mode lets you keep track of time in a different zone. The Dual Time
TME: Timekeeping Mode setting can be a time that is ?23 hours from the watchOs current time setting.
CHR: Stopwatch " The seconds count of the Dual Time Mode is synchronized with the seconds count
(Chronograph) Mode of the Timekeeping Mode.
L-TM: Dual Time Mode
ALM: Alarm Mode
24-hour hand Minute hand
First click
Timekeeping(Setting day)
The watchOs calendar normally makes allowances for different month lengths.
However, you will have to adjust the date manually in the case of leap years.Second hand
24-hour hand Minute hand Second click
Hour hand (Setting time)
First click Mode hand Crown (Normal position)
(Setting day) Day
Hour hand
To change the Dual Time setting
Second hand 1. With the crown in the normal position, rotate it until the mode hand is pointed at L-
Second click TM (Dual Time Mode).
(Setting time)
" This will cause the hour and minute hands to move to the current Dual Time setting.
2. Pull the crown out to the second click.Mode hand Crown (Normal position)
3. Rotate the crown to change the Dual Time setting.
Day
" Rotating the crown one turn towards you until you feel a click will return the current
setting one hour.
To set the time" Rotating the crown one turn away from you until you feel a click will advance the
1. With the crown in the normal position, rotate it until the mode hand is pointed atcurrent setting one hour.
TME (Timekeeping Mode)." There is no high-speed hand movement when setting changing the Dual Time
2. Pull the crown out to the second click to stop the second hand.setting.
3. Rotate the crown to set the current time with the hour and minute hands." Change the setting carefully, making sure to distinguish between AM and PM.
" Rotating the crown one turn towards you until you feel a click will return the current4. After you are finished, push the crown back in to the normal position.
time setting one minute.
" Rotating the crown one turn away from you until you feel a click will advance the
current time setting one minute.
" Rotating the crown two or more turns will move the hands at high speed. To stop
high-speed hand movement, rotate the crown towards you or away from you one
turn. If you do not stop high-speed hand movement, it will stop automatically after a
12-hour cycle.
" Set the time carefully, making sure to distinguish between AM and PM.
4. Push the crown back in to the normal position to restart timekeeping.
1 |
ACEC
