Module No. 23872387-1
GENERAL GUIDE
? Press C to change from mode to mode.
? In any mode (except when making any settings), press L to illuminate the display.
Alarm ModeStopwatch ModeDual Time Mode
Calendar ModeTimekeeping Mode
Press C.
CALENDAR MODEALARM MODE
To set the date
Hold down B.Press B.
Year
Hold down B.
Hour
Month
DayPress B.
Press B.Press B.
Minutes
MonthDay of weekPress B.
Hour
DayMinutes
Mode indicator
1.In the Calendar Mode, hold down B for about two seconds, until OADJ� and then
the year digits flash on the display. Keep B depressed until the year digits flash.When an alarm is turned on, an alarm tone sounds for 20 seconds at the preset time
2.While any setting is selected (flashing), press C to increase it. Holding down Ceach day.
changes the flashing setting at high speed.
3.Press B to move the selection around the display in the above sequence.To set the alarm time
? The day of the week is automatically set in accordance with the date.1.In the Alarm Mode, hold down B for about two seconds, until OADJ� and then the
? The date can be set with the range of January 1,1995 to December 31, 2039.hour digits flash on the display. Keep B depressed until the hour digits flash.
? If you do not operate any button for a few minutes while a selection is flashing, the2.Press C to increase the setting. Holding down C changes the current setting at
flashing stops and the watch goes back to the Calendar Mode automatically.high speed.
3.Press B to change the selection in the above sequence.
? The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
? When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
TIMEKEEPING MODE
? If you do not operate any button for a few minutes while a selection is flashing, the
The minutes hand advances 1/3 of a minute each time the secondOs count in theflashing stops and the watch goes back to the Alarm Mode automatically.
digital display reaches 00, 20 and 40 seconds.? The alarm is turned on automatically whenever you change the alarm time setting.
To set the digital timeTo stop the alarm
Press any button to stop the alarm after it starts to sound.
Hold down B.Press B.
SecondsHour
To switch the daily alarm on and off
In the Alarm Mode, press B to turn the daily alarm on and off.
Press B.
ONOFF
12/24MinutesPress B.
Press B.Press B.
Hour
Seconds
PM indicator
Minutes
To test the alarm
1.In the Timekeeping Mode, hold down B for about two seconds, until OADJ� andHold down C while in any mode to sound the alarm.
then the secondOs digits flash on the display. Keep B depressed until the secondOs
digits flash.
2.While the secondOs digits are selected (flashing), press C to reset the seconds to
00. If you press C while the secondOs count is in the range of 30 to 59, the sec-
onds are reset to 00 and 1 is added to the minutes. If the secondOs count is in the
range of 00 to 29, the minuteOs count is unchanged.STOPWATCH MODE
3.Press B to move the selection around the display in the above sequence.The Stopwatch Mode lets you measure elapsed time. The
4.While hour or minutes are selected (flashing), press C to increase the setting.range of the stopwatch is 23 hours, 59 minutes 59 sec-
Holding down C changes the current setting at high speed. While the 12/24-houronds. The measuring unit for the first hour of elapsed
setting is selected, press C to switch between the two formats.time measurement is 1/100-second. After that the unit is
? If you do not operate any button for a few minutes while a selection is flashing, theone second.
flashing stops and the watch goes back to the Timekeeping Mode automatically.
To measure elapsed time
Hand setting
1.Press B to start the stopwatch.
Each press of A advances the hands 20 seconds. Holding down A advances the2.Press B again to stop the stopwatch.
hands at high speed.? You can repeat steps 1 and 2 as many times as you
? Note that the hands can be advanced only and cannot be moved back. Take carewant.
so you do not go past the setting you want to make.3.To reset the stopwatch time to all zeros, hold down B.
Minutes1/100 secondsAfter the first hour
Seconds
Mode indicatorHourSeconds
ABOUT THE BACKLIGHTMinutes
In any mode (except when making any settings), press L to illuminate the display
for about two seconds.
? The backlight of this watch illuminates both the digital display and analog face.
? The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
? The backlight automatically stops illuminating whenever an alarm sounds.
? Frequent use of the backlight shortens battery life. |
ACEC
