Module No. 22582258-1
GENERAL GUIDE
?Press C to change from mode to mode.
?Pressing L in any mode illuminates the display for about 2 seconds.
?If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.
?When making settings, note that you can scroll only forward, you cannot scroll back. This means that if you go past the setting you want, you must scroll through all of the available
settings again until the one you want reappears.
Timekeeping ModeStopwatch ModeRecall ModeDay Counter ModeAlarm Mode
Press C.
TIMEKEEPING MODEABOUT THE BACKLIGHT
Hour : Minutes?Press D to toggle between 12-hour and 24-hour time-?Press L to illuminate the display for about 2 seconds.
keeping.?The backlight of this watch employs an electro-luminescent (EL) light, which loses
PM indicator Seconds?When the 12-hour format is selected, the indicator Pits illuminating power after very long term use.
appears on the display for times from noon to 11:59 p.m.?Frequent use of the backlight shortens the battery life.
to indicate Op.m.� There is no indicator for Oa.m.� times.?The watch emits an audible sound whenever the display is illuminated. This does
?The indicator P does not appear when you are usingnot indicate malfunction of the watch.
24-hour timekeeping.?The illumination provided by the backlight may be hard to see when viewed under
?The display contents of the watch will not change if youdirect sunlight.
switch between 12-hour and 24-hour timekeeping while?The backlight automatically turns off whenever an alarm sounds.
the current time is between 1:00 a.m. and 11:59 a.m.
Month - DaySTOPWATCH MODE
Day of weekAbout Lap times and Split times
DST on indicator
Setting the Time and Date
There are two different ways to set the time and date. The procedure you should useLap Times
depends on whether you want to make major changes or minor changes to the cur-A lap time is the amount of time it takes for you to get from one point to
rent setting.another during a race. When running on a track, for example, you can time
how long it takes you to complete each lap.
When you want to do this:Use this procedure:
Split Times
Make major changes to the time and
A split time is the time from the start of a race until the point that the split isdate setting (before using the watch
OTo make major time and date settings�measured. For example, you could measure split times to determine how
for the first time, after having the bat-
tery replaced, etc.)long it takes for you to get from the starting line to the 5-kilometer mark, the
10-kilometer mark, etc.
Make minor adjustments (within about
OTo zero-reset the minutes and sec-
onds (EASY ADJUST )�30 minutes of the current setting) to
the time setting Mode indicatorThe Stopwatch Mode lets you measure elapsed time, lap
times, and split times. The range of stopwatch is 23 hours,
59 minutes, 59 seconds. The first hour of a stopwatch
To make major time and date settingsoperation is measured in units of 1/100 second. After that,
1.While in the Timekeeping Mode, hold down A until the seconds digits flash on theelapsed time is measured in units of one second. You
display, indicating the setting screen.can use the EL backlight by pressing L at any time while
2.Press C to move the flashing in the sequence shown below.the stopwatch is operating.
SecondsDST on/offHour
DayMonthYearMinutes
3.While the seconds setting is selected (flashing), press D to reset it to 00. If you
press D while the seconds setting is in the range of 30 to 59, the seconds are
reset to 00 and 1 is added to the minutes. If the seconds setting is in the range of
00 to 29, the minutes count is unchanged.SecondsMinutes
?While the DST* setting is selected (DST on indicator is flashing), press D to toggleMinutes1/100 secondHoursSeconds
it on (on) and off (OFF).
4.While any other setting is selected (flashing), press D to increase it. Holding down
D changes the setting at high speed.Lap timeLap time
5.After you make the settings you want, press A to exit the setting screen.
?The day of the week is automatically set in accordance with the date.
?The date can be set within the range of January 1, 2000 to December 31, 2039.Split timeSplit time
?The watchOs built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be noMinutes 1/100 secondHours Seconds
reason to change it except after the replacement of the watchOs battery.SecondsMinutes
*Daylight Saving Time (DST), which is also sometimes called Osummer time� ad-[Up to 1 hour][After 1 hour]
vances the time for one hour, as is the custom in some areas during the summer.
Remember that not all countries or even local areas use Daylight Saving Time.?In the Stopwatch Mode, the upper part of the display shows lap times, while the
lower part shows split times. When recalling times in the Recall Mode, you can
To zero-reset the minutes and seconds (EASY ADJUST)display either lap times or split times in the upper part of the display. The lower part
1.A few seconds before the arrival of the time on which you want to zero-reset theof the display shows the corresponding lap time or split time number. Note that the
minutes and seconds, hold down button B.lap/split time count value appears on the display in the Recall Mode only. It is not
2.While still holding down button B, press button D when the time on which youdisplayed in the Stopwatch Mode.
want to zero-reset the minutes and seconds arrives.
?The watch beeps to let you know that the minutes and seconds were reset to 00:00.To measure elapsed time
3.Release buttons B and D.1.Press D to start the stopwatch.
?If you press B and D while the minutes count is in the range of 30 to 59, they are2.Press D to stop the stopwatch.
reset to 00 and 1 is added to the hour. If the minutes count is in the range of 00 to?You can resume the elapsed time measurement operation by pressing D again.
29, the hour count is unchanged.?You can stop the elapsed time measurement operation by pressing D again.
?Though the beep may sound slightly after the point you press both buttons, the3.While the elapsed time is stopped on the display, press B to clear the stopwatch
zero-reset setting should be correct.to all zeros. |
ACEC
