CROSSLEE G508S.HOTTOASTER Instruction Manual

$4.99

CROSSLEE G508S.HOTTOASTER - It's a complete owner's manual ( also known as operating manual or user guide), and it's in PDF format. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

Krzysztof Mazurek - 11/27/2007

Super ! Szukałem wszędzie i tutaj po 10 minutach miałem schemat w swoim PC.

ivan radic - 02/03/2007

Super fast!Excellent quality and solid transaction!I will return.Thanks

Aaron Lawrence - 01/02/2008

Contains mechanism diagrams, parts lists and schematics for all worldwide versions of DC-X88Z. Also includes remote schematic etc. A few non-essential pages are missing such as specifications. Includes the mechanical and electronic calibration instructions for the tape decks.

Jacek Madej - 08/30/2008

Hi! love you!! schematics circuit best scan electronics area ...a have old radio grundig c8000 seek from net ... very done... hello best regard Edi from Poland

Gaspar Lovas - 11/03/2009

That's all right, thank you for all your trouble. Yours sincerely GL

Customers who bought this product also purchased

CROSSLEE CL372BV-031237215590 Owner's Manual	CROSSLEE CL372GV-031237215790 Owner's Manual	CROSSLEE 010208950241F.S.1 Owner's Manual
CROSSLEE 010205116281FS5 Owner's Manual	CROSSLEE 797C-031279715003 Owner's Manual	CROSSLEE CL322SW-031232215390 Owner's Manual

Click to see text excerpt from the manual

3. TO REPLACE THE IGNITER LEAD
" Withdraw the burner assembly as detailed in 2.1
to 27
" Unplug the igniter lead from the electrode and
piezo igniter. Replace igniter lead.
" Reassemble all components in reverse order of
removal, check spark and ignition.
4. TO REPLACE THE OXY-PILOT ASSEMBLY
The assembly is not an item that can he serviced as part of its calibration depends on the proximity of the
spark electrode and thermocouple tip it is replaced as follows: -
" Withdraw the burner assembly as detailed in 2.1 to 2.7
" Undo the tube nut and tube from the base of the pilot and the thermocouple from the tap/FSD.
" Remove the two screws securing the bracket to the framework. Replace the oxy-pilot assembly.
" Reassemble all the components in reverse order of removal ensuring that the solenoid lead is connected.
5. CLEANING THE PILOT
" Clean off any lint or fluff and clean the injector taking care to avoid damage. The gap between the
electrode and the thermocouple is that shown in Fig 22.
6. TO CLEAN OR REPLACE THE INJECTOR
" Withdraw the burner assembly as detailed in 2.1 to 2.2
" Undo the pilot supply and the thermocouple from the rear of the gas control and disconnect the HT lead
from the piezo igniter.
" Disconnect the burner supply by undoing the compression nut on the elbow injector. Now undo the two
securing screws at the front of the burner assembly to remove the control panel complete with tap and
piezo igniter.
" Pull the burner forward off the injector and remove the burner. Remove the two screws fixing the aeration
sleeve and remove the sleeve and aeration closure plate away from the injector noting its correct position.
Undo the injector elbow-securing nut and remove the injector.
" Clean or replace the injector ensuring that its securing nut is only finger tight to allow it its correct
orientation when connected to the burner supply pipe.
" Reassemble in reverse order of removal ensuring correct positioning of the aeration sleeve and closure
plate. Check for gas soundness.
Page 22