ENGLISH
#9Number buttons$1REPEAT switchiSerial control port!1MONO OUT ON/OFF switch
Y When set to the OON� side, repeat play modeY Select the signal from the balanced outputs of
(1, 2, 3, 4, 5, 6, 7, 8, 9 and 0/CLEAR)(DN-T645 : RS232C/RS422A,
Y Use these buttons for the direct search andis set.CD and cassette deck.
DN-T625 : RS232C)
Y The selected track is played repeatedly when inOFF : Stereo signal output (Normal)
program memory functions.
Y This is serial remote connector.
Y For direct search, press for example buttonthe single play mode, and all the tracks on theON : L/R mixed monaural signal output with
Y Applicable connector : 9-pin D-sub (male)
disc are played repeatedly when in thedifferent levels
if you want to hear track number 3.
Y Baud rate : 9600 bps
continuous play mode.
Y Pin layoutMonaural Output Signal Level
For track number 12, press then .Y The REPEAT switch functions in the normal
CDCassette deck
play, program play, and random play modes.RS-232C
To program tracks, press the PROGRAM/DIRECT
Y When set back to the OOFF� side, the normalL channel :+18 dBu+4 dBu
button $0 to set to the program mode.Pin No.Signal NameI / O
play mode is set.HIGH(Normal level)(Normal level)
1GND_
$0PROGRAM/DIRECT button6NC_R channel :_10 dBu_10 dBu
$2PLAY MODE switch
Y Press this button when you want to enterLOW
Y Use this to select the play mode.2TxDO
tracks for programmed playback. (Refer to_
Y The PLAY MODE switch functions in the_= LOW level (10 dBu) of R channel could be
page 11 for details.)7NC
normal play, program play, random play and A-convenient when you need to feed the output
Y When the button is pressed, the OPROG�3RxDI
B repeat play modes.of DN-T645/625 into a Mic level input terminal
indicator is lit._
SINGLE : (single track play mode)8NCon mixer console etc. in order to avoid overload
The stop mode is set after the specified track4NC_by normal Line level input.
is played._
9NC
CONT. : (continuous play mode)!2BALANCED OUT (TAPE/MIX)
_
The stop mode is set after the last track is5S. GROUNDconnectors
played.Y These are active balanced outputs using XLR
RS-422A (DN-T645 only)
type connectors. The tapeOs playback signals or
Pin No.Signal NameI / Othe mixed tape and CD playback signals are
(2) Rear panel1GND_output from these connectors.
6S. GROUND_Y Pin layout : 1. Common / 2. Hot / 3. Cold
qUNBALANCED IN jacksrDIGITAL OUT (CD) jackY Applicable connector :2TxD (RETURN)O
Y These are unbalanced inputs using RCA typeY This is an coaxial output using an RCA typeCannon XLR-3-31 or equivalent
jacks.jack.7TxDO
NOTE :
Use them to input signals to be recorded on aY Signal format : SPDIF or IEC-958 Type II3RxDI
Y Do not short-circuit the hot or cold pin with
tape.8RxD (RETURN)I
the common pin.
tExternal synchronized control jacks_
4NC
wUNBALANCED OUT (TAPE/MIX) jacks(EXT. SYNC.)
_
9NCBALANCED IN connectors
Y These are unbalanced outputs using RCA type!3
Y Connect these for synchronized recording.
jacks._Y These are active balanced inputs using XLR5NC
type connectors. Use these connectors to
The tapeOs playback signals or the mixed tape
yCascade control jacks (CASCADE)
and CD playback signals are output from theseoParallel remote control portinput signals to be recorded on a tape.
Y Connect these for continuous operation on
Y Pin layout : 1. Common / 2. Hot / 3. Cold
jacks.multiple units.(PARALLEL) (DN-T645 only)
Y Applicable connector :
Y When the RELAY MODE switch !3 is set toY This is a parallel remote connector.
eUNBALANCED OUT (CD) jacksOCASCADE�, the start signal is output fromY Applicable connector : 25-pin D-sub (male)Cannon XLR-3-32 or equivalent
Y These are unbalanced outputs using RCA typeY Connecting signal layout : See page 9.
this output jack once operation of Deck side isINPUT SELECT switch
!4
jacks.finished.
Y Use this select the recording input signals
The CDOs playback signals are output from!0BALANCED OUT (CD) connectors
(BALANCED or UNBALANCED).
these jacks.Y These are active balanced outputs using XLR
uRC IN control jack
type connections. The CDOs playback signals
Y This is a stereo mini jack for wired remote
are output from these connectors.
control.
Y Pin layout : 1. Common / 2. Hot / 3. Cold
Y Applicable connector :
Cannon XLR-3-31 or equivalent.
NOTE :
Y Do not short-circuit the hot or cold pin with
the common pin.
7 |
ACEC
