Ensure that the lid is closed after every refill.
Filling with salt
Only use salt specifically designed for use inTop up with rinse aid when the rinse aid indicator light on the
dishwashers.control panel illuminates.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
softener.Adjusting the dose
Only fill with salt just before starting one of the complete
According to the finish and drying results obtained, adjust the
washing programmes.
dose of rinse aid by means of the 6 position selector (position
This will prevent any grains of salt or salty water, which
1 minimum dosage, position 6 maximum dosage).
may have been spilt, remaining on the bottom of the
machine for any period of time, which may causeIncrease the dose if there are drops of water or lime spots on
corrosion.the dishes after washing.
The dose is factory set in
position 4.
To fill:
Reduce it if there are sticky
1.Open the door, remove the lower basket and unscrew the
whitish streaks on the dishes.
cap of the salt container by turning it anticlockwise.
2.Pour 1 litre of water inside the container (this is necessary
only before filling with salt for the first time).
3.Using the funnel provided,
SALE
pour in the salt until the ZOUT
SALT
container is full.
SALZ
SEL
4.Replace the cap making
sure that there is no trace
of salt on the screw thread Clean up any rinse aid spilt during filling with an
or on the gasket.absorbent cloth to avoid excess foaming during the next
wash.
5.Screw on the cap tightly
turning it clockwise until it Only use branded rinse aid for dishwashers. Never fill the
SR14
stops with a click.rinse aid dispenser with any other substances (e.g.
dishwasher cleaning agent, liquid detergent). This would
damage the appliance.
The salt container will require topping up periodically. You are
reminded of this by the salt indicator light on the control panel
which comes on when the salt has finished.
Deactivation of the inflow of rinse aid
The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been(The dishwasher must be switched off)
replenished, assuming the dishwasher remains switched
When the inflow of rinse aid has been deactivated, also
on. If you are using salts that take longer to dissolve then
the rinse aid indicator light on the control panel is
this can take longer. The function of the machine is not
automatically deactivated.
affected.
Do not worry if water over flows from the unit when filling with1.Press the On/Off push button, all indicator lights of the
salt, this is quite normal.programme push buttons will illuminate (setting mode).
2.Press simultaneously function push buttons 2 and 3, the
indicator lights of the function push buttons 1, 2 and 3 start
Rinse aid flashing.
Rinse aid is automatically added during the last rinse, ensuring
thorough rinsing, and spot and streak free drying. 3.ThePress the function push button 2, the indicator lights of
dispenser, which is positioned inside the door, holds about 1function push buttons 101 and 3 turn off while the indicator
ml of rinse aid, which is sufficient for 16 - 40 dishwashinglight of the push button 2 goes on flashing, at the same time
programmes, depending upon the dosage setting. the "end of programme"indicator light illuminates
indicating that the inflow of rinse is active.
Filling with rinse aid
4.To deactivate the inflow of rinse aid, press again the
1.Open the container by pressing the release button (A). function push button 2, the "end of programme"indicator
light turns off, indicating that the inflow of rinse aid has been
2.Add the rinse aid until the container is completely full. The
deactivated.
maximum level for filling is indicated by "max".
5.To memorise the operation, switch off the dishwasher by
pressing the On/Off push button or wait about 60 seconds
after which the dishwasher will automatically return to
setting mode.
24 |
ACEC
