CUE INSTRUCTIONS:SPECIFICATIONS:
1. To start the play at a point other than the beginning of a track, followGENERAL:
these instructions:
Disc Type................................Standard Compact discs (12 cm & 8 cm)
First choose the track you wish to play, and then press PLAY/PAUSETime Display.....................Track Elapsed, Track Remain, or Total remain
(9) so the unit goes into the play mode. Press PLAY/PAUSE (9) to
pause play at the spot where you want the play to start the CUEVariable Pitch......................................? 16% Slider with Resume Switch
POINT. Use the SEARCH BUTTONS (7) to pick the precise spot youStart...........................................................................Within 0.03 seconds
want play to begin, then press PLAY/PAUSE (9) again to save the cueTrack Selection.....................................................................1 to 99 Tracks
point. Press the CUE (8) button to pause play at the cue point (the unit
will go into the pause mode and the location indicated on the displayAUDIO SECTION:
will be the memorized cue point). You can preview the cue point by
pressing and holding down CUE (8). Press PLAY/PAUSE (9) to beginQuantization......................................1 Bit Linear/Channel, 3 Beam Laser
play from the cue point.
NOTE: AFTER A CUE POINT IS SET, PRESSING THE TRACK SKIPOversampling Rate..........................................................................8 Times
(6) BUTTONS CLEARS THE CUE POINT. WHEN YOU PRESS THESampling Frequency.....................................................................44.1 kHz
CUE (8) BUTTON IN THE NEW TRACK, THE BEGINNING OFFrequency Response......................................................20 Hz to 20 kHz
THAT TRACK WILL BE THE NEW CUE POINT.Total Harmonic Distortion..............................................Less Than 0.005%
2. Once you have saved a cue point you can fine tune or change theSignal to Noise Ratio.....................................................................>96 dB
memorized cue point:Dynamic Range.................................................................................>94 dB
To change a cue point, push PLAY/PAUSE (9) so the unit plays fromOutput Level (nominal)........................................................1.9 Volts R.M.S.
the cue point, then press PLAY/PAUSE (9) at the spot you wish your
Power Supply.......................................................AC 120/230V, 60/50 Hz
new cue point to be. Press PLAY/PAUSE (9) again to save the cue
point. The unit will go into the pause mode and the location indicated onDimensions...............................8.38? x 8.86? x 3.75? (213 x 225 x 95 mm)
the display will be the new memorized cue point.Weight..................................................................................4.5 lbs. (2 kg)
To fine tune a cue point, pause play at the memorized cue point, then
use the SEARCH (7) buttons to scan frame by frame (1/75th of a* Specifications and design are subject to change without notice
second) to where you want play to begin. Press PLAY/PAUSE (9) tofor purpose of improvement.
save the new cue point.
NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT
(TO HELP YOU FIND THE BEAT). THE STUTTERING EFFECT
WILL END WHEN YOU PRESS PLAY/PAUSE (9) TO SAVE THE
CUE POINT. ALSO, DURING FINE TUNING IF YOU HOLD DOWN
THE SEARCH (7) BUTTON, THE UNIT WILL SCAN QUICKLY
AFTER 10 FRAMES.
TROUBLE SHOOTING:
? If the disk will not play, check to see if the disc was loaded correctly
(label side up). Also check the disc for excessive dirt, scratches, etc.
? If the disc turns but there is no sound, check the cable connections. If
they are okay, check your amplifier or receiver.
? If the CD skips, check the CD for dirt or scratches. Do not assume that
the CD player is defective. Many CDs are recorded out of spec and will
skip on most or all CD players. Before sending the unit in for repair, try
playing a CD that you are sure plays properly.
(4) |
ACEC
