Menu OperationsMenu Operations
Quick Reference Guide for PC Menu ModeBasic Menu Operation
Main Menu in PC Menu Mode (While receiving computer-related signals)When the MENU button is pressed, the projector enters Video or PC menu mode by responding to the input signal being
Image adj. ? (Refer to page 48)received.
Brightness:Brightness of the picture image being projected can be adjusted. (�30 to +30, 0*)
Contrast:Contrast of the picture image being projected can be adjusted. (�30 to +30, 0*)Video menu mode:
4Press the cursor button 5 or to
Sharpness:Adjust the outline of letters etc. (1 / 2 / 3 / 4 / 5, 3*)Enters this mode when video-device-related signals are
All reset:Resets above items to the factory set values.input from the following devices.select an item in the submenu.
Yes / NoY Video devices connected to the VIDEO IN (Y/C and When a OLanguage� has been selected in step 2, press
SettingVIDEO) terminals.to set the language.
Tracking:The lateral size and display area of picture image can be adjusted. (�128 to +127)Y A video device connected to the PC 2 terminals, which Remote control unitProjector
? (Refer to page 46)outputs component signals (Y, B-Y, R-Y) or DTV-format
Phase:Flickering or dim picture image can be adjusted. (0 to 31) ? (Refer to page 46)signals (Y, PB, PR).
Position:Video screen position and menu position can be adjusted. ? (Refer to page 50)PC menu mode:
Disp. Posi. / MenuEnters this mode when computer-related signals are input
Resize:The relationship between the number of pixels (resolution) and the screen can be selected. from the following devices.
? (Refer to page 52)Y A computer connected to the PC 1 terminal.
O1:1�:Picture image is projected with its original size.Y A computer connected to the PC 2 terminal, which outputs
analog RGB, V, H/Cs signals.
Panel:Picture image is enlarged to the full size.5Press the cursor button 2222 or 3333 to set
Aspect*:Picture image is enlarged while maintaining the original aspect ratio.
or adjust the value.
ClampSelectable clamp position. Normally, set to OBP�. ST / FP / BP*
1Press the MENU button.Remote control unitProjector
Color temp.
The main menu is displayed on the screen.
Color temp.:Adjustable color temperature, Low/Middle* /High.
-Will be adjusted to correct reddish or blueish image.Remote control unitProjector
R-Gain:Adjusts the red level. (o to 255, the adjustable range varies depending on signals)MENUMENU
G-Gain:Adjusts the green level. (o to 255, the adjustable range varies depending on signals)
B-Gain:Adjusts the blue level. (o to 255, the adjustable range varies depending on signals)
All-reset:Reset above items to the factory set values.
Yes/NoWhen an item which has the OENTER� message has been
Options ? (Refer to page 53)selected in step 4, press the ENTER button to move to the
Options 12Press the cursor button 5 or to next submenu.
Menu display: 15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.) select an item in the main menu.Y All reset? (Refer to page 48)
Line display: 5sec* (Line display such as OPC1� or OPC2� appears on top right of the screen for 5 seconds Y Position? (Refer to page 50)
Remote control unitProjector
when the VIDEO or PC button is pressed.) / OFF (Line display does not appear.)Y Decoder? (Refer to page 44)
Keystone:Press ENTER to enter the Keystone submenu.Y Keystone ? (Refer to page 53)
ENGLISHY Options 1 ? (Refer to page 53)
Keystone:Adjust to correct the trapezoidal distortion of the projected image.
(�80 to +128, 0*)Y Options 2 ? (Refer to page 53)
PC2 (BNC):RGB or YPBPR*. Set to RGB when a computer device with analog RGB, V, H/Cs signals is To exit the main menu:
connected to the PC2 terminals. Set to YPBPR when a device with component signals (Y, B-Y While the main menu is displayed, press the MENU button.
Y, R-Y) or DTV-format signals (Y, PB, PR) are connected to the PC2 terminals.The main menu disappears and the original picture image
Options 2:Press ENTER to enter the OOption 2� submenu.resumes.
Right Left rev.:OFF* / ON (Select for upside-down hanging on the ceiling.)3Press the cursor button 3333 or the To exit the submenu:
DEUTSH
Top Bottom inv.:OFF* / ON (Select for upside-down hanging on the ceiling.) ENTER button to enter the submenu.Y While the submenu is displayed, press the EXIT button.
RS-232C [bps]:Selectable baud rate (transmission speed). 9600 / 19200*The submenu corresponding to the item selected in step The menu returns to the previous menu.
Sleep time [min:]Selectable sleep times. If no-signal condition continues for the period 2 is displayed on the screen.Y To exit the menu mode directly, press the MENU button.
of selected time (Unite: Minutes), the projector enters the stand-by *When you selected Information in step 2, no The submenu disappears and the original video image is
mode. 15 / 30 / 60 / OFF*submenu is available.restored.
Options 1:Press ENTER to return to the OOption 1� submenu.
Remote control unitProjector
LanguageLanguage for on-screen display. ? (Refer to page 45)
Japanese / English* / German / Spanish / Italian / FrenchFRAN�AIS
Information ? (Refer to page 55)
Input:Shows the terminal name selected by the PC button. (PC1or PC2)
Switcher:This display currently has no meaning. (OCH.0� is usually displayed to indicate that it is not being used.)
Resolution:Shows the resolution of the input signal being received. (Horizontal � Vertical)
It may not be displayed correctly with some input signals.
Frequency H: Shows the horizontal frequency of the input signal being received. ( kHz)ITALIANO
Frequency V: Shows the vertical frequency of the input signal being received. ( Hz)
Lamp time:Accumulated used hours of the light-source lamp.
*: Factory set value.
ESPANOL
4142 |
ACEC
