� Slots and openings in the cabinet are provided for ventila-� The product should be placed more than one foot away from
tion. These ensure reliable operation of the product and pro-heat sources such as radiators, heat registers, stoves, and
tect it from overheating. These openings must not be blockedother products (including amplifiers) that produce heat.
or covered. (The openings should never be blocked by plac-� When connecting other products such as VCROs, and per-
ing the product on bed, sofa, rug, or similar surface. It shouldsonal computers, you should turn off the power of this prod-
not be placed in a built-in installation such as a bookcase oruct for protection against electric shock.
rack unless proper ventilation is provided and the� Do not place combustibles behind the cooling fan. For ex-
manufacturerOs instructions have been adhered to.)ample, cloth, paper, matches, aerosol cans or gas lighters
For proper ventilation, separate the product from other equip-that present special hazards when over heated.
ment, which may prevent ventilation and keep a distance of� Do not look into the projection lens while the illumination
more than 11-7/8" (30 cm).lamp is turned on. Exposure of your eyes to the strong light
� This product should be operated only with the type of powercan result in impaired eyesight.
source indicated on the label. If you are not sure of the type� Do not look into the inside of this unit through vents (ventila-
of power supply to your home, consult your product dealertion holes), etc. Do not look at the illumination lamp directly
or local power company.by opening the cabinet while the illumination lamp is turned
� This product is equipped with a three-wire plug. This plugon. The illumination lamp also contains ultraviolet rays and
will fit only into a grounded power outlet. If you are unable tothe light is so powerful that your eyesight can be impaired.
insert the plug into the outlet, contact your electrician to� Do not drop, hit, or damage the light-source lamp (lamp unit)
install the proper outlet. Do not defeat the safety purpose ofin any way. It may cause the light-source lamp to break and
the grounded plug.lead to injuries. Do not use a damaged light source lamp. If
�Power-supply cords should be routed so that they are notthe light-source lamp is broken, ask your dealer to repair it.
likely to be walked on or pinched by items placed upon orFragments from a broken light-source lamp may cause inju-
against them. Pay particular attention to cords at doors,ries.
plugs, receptacles, and the point where they exit from the� The light-source lamp used in this projector is a high pres-
product.sure mercury lamp. Be careful when disposing of the light-
�For added protection of this product during a lightning storm,source lamp. If anything is unclear, please consult your
or when it is left unattended and unused for long periods ofdealer.
time, unplug it from the wall outlet and disconnect the cable� Do not ceiling-mount the projector to a place which tends to
system. This will prevent damage to the product due to light-vibrate; otherwise, the attaching fixture of the projector could
ning and power line surges.be broken by the vibration, possibly causing it to fall or over-
� Do not overload wall outlets, extension cords, or convenienceturn, which could lead to personal injury.
receptacles on other equipment as this can result in a risk� Use only the accessory cord designed for this product to
of fire or electric shock.prevent shock.
�Never push objects of any kind into this product throughThe power supply voltage rating of this product is AC 120 V,
openings as they may touch dangerous voltage points orAC 100 V� AC 240 V, the power cord attached conforms to
short out parts that could result in a fire or electric shock.the following power supply voltage. Use only the power cord
Never spill liquid of any kind on the product.designated by our dealer to ensure Safety and EMC.
� Do not attempt to service this product yourself as openingWhen it is used by other power supply voltage, power cable
or removing covers may expose you to dangerous voltagesmust be changed.
and other hazards. Refer all service to qualified service per-Ensure that the power cable used for the projector is the
sonnel.correct type for the AC outlet in your country.
� Unplug this product from the wall outlet and refer service toConsult your product dealer.
qualified service personnel under the following conditions:
a) When the power supply cord or plug is damaged.Power cord
b) If liquid has been spilled, or objects have fallen on the
product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the Operation Manual, as an improper ad-For UnitedFor European
justment of controls may result in damage and will oftenKingdomcontinent countries
require extensive work by a qualified technician to re-
store the product to normal operation.Power cord
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in perfor-
mance - this indicates a need for service.
� When replacement parts are required, be sure the servicePower supply voltage: AC 120 V
technician has used replacement parts specified by the
manufacturer or with same characteristics as the original*DO NOT allow any unqualified person to install the unit.
part. Unauthorized substitutions may result in fire, electricBe sure to ask your dealer to install the unit (e.g. attaching
shock, or other hazards.it to the ceiling) since special technical knowledge and skills
� Upon completion of any service or repairs to this product,are required for installation.
ask the service technician to perform safety checks to de-If installation is performed by an unqualified person, it may
termine that the product is in proper operating condition.cause personal injury or electrical shock.
3 |
ACEC
