HOW TO USE OSETUP MENU� (cont'd)
STATUS DISPLAY OVER LEVEL ( )
Sets the input levelOs lower limit indicated in red for
Sets the status display ON/OFF.
the O3COLORS� display.
* Switches the display on and off. Also selects the type of
display. (When an input card compliant with AUDIOY �8dB/�6dB/�4dB/�2dB
LEVEL METER is installed.)
BAR BRIGHTNESS ( )
* Switches the AUDIO PLL setting. (When SDI input card
compliant with EMBEDDED AUDIO is installed.)Selects the brightness of the AUDIO LEVEL METER
display.
Press the button to
<STATUS DISPLAY>HIGH : Brighter
display the setting menu
STATUS DISPLAY: ONLOW : Darker
illustrated on the right.LEVEL METER ch:31"24
BAR TYPE :3COLORS
REFERENCE LEVEL : -20dB
NOTE:OVER LEVEL : -4dBAUDIO LEVEL METER display example
BAR BRIGHTNESS : HIGH
Function setting is displayedLEVEL METER ch: 1-8, BAR TYPE: 3COLORS
when input card compliant with
EXIT: MENU ADJUST:- + SELECT:
AUDIO LEVEL METER is
installed.
OVER LEVEL
[�8dB/�6dB/�4dB/�2dB]
STATUS DISPLAY
Sets the status display ON or OFF.
REFERENCE
ON : The information is displayed.
LEVEL [�20dB/
OFF : The information is not displayed.�18dB]
LEVEL METER ch
1 2 3 45 6 7 8
Selects the audio channels used in the AUDIOAudio channels and OVER/REFERENCE
level indication
LEVEL METER display.
Y OFF/1:2/12:34/31:24/123:456/1-8
NOTES:CONTROL LOCK
Y Numbers indicate the audio channel. The channel input level
indicated on the left side of O:� is displayed on the left side of the CONTROL LOCK
screen, and the channel input level indicated on the right side of
Invalidates most of operations on the front panel
O:� is displayed on the right side of the screen.
Y AUDIO LEVEL METER is not displayed when this is set to OFF.(including menu screen operations).
Y When O1-8� is selected, the channel input level for 1, 2, 3 and 4 isOFF : Enables normal operations.
displayed on the left side of the screen, and the channel inputON : Invalidates all operations except the power switch
level for 5, 6, 7 and 8 is displayed on the right side of the screen.
and CONTROL LOCK.
NOTES:
BAR TYPE
Y While CONTROL LOCK is set to ON, attempting to perform any
Selects the color of the audio level meter.
operation except power switch and CONTROL LOCK causes the
WHITE-1: White color displayO Control lock on!� warning to appear on the screen for approx.
3 seconds. (It is possible to operate the power switch and display
WHITE-2: White (half transparent) display
SETUP MENU.)
3 COLORS : The audio level meter uses three different
Y When SETUP MENU is displayed while CONTROL LOCK is set
colors (red, yellow and green) to indicate
to ON, the cursor (4) is located next to CONTROL LOCK and
variations in input levels.
cannot be moved.
Red: displayed when the audio input exceeds the
level set in OOVER LEVEL�.
all reset
Yellow : displayed when the audio input exceeds the
level set in OREFERENCE LEVEL�.Resets all SETUP MENU items to factory-preset
Green : displayed when the audio input does notvalues.
exceed the level set in OREFERENCE1. Select Oall reset� by / buttons, then press button.
LEVEL�.Confirmation message is displayed.
NOTES:2. To initialize, press button.
Y For WHITE-1 and WHITE-2, the line indication for the standardTo cancel the initialization, press the MENU button.
input level set in the OREFERENCE LEVEL� is displayed. Input
level set in the OOVER LEVEL� is not displayed.
Y As for the audio channel bar display with no signal input, white is
displayed for the 3COLORS setting, and gray is displayed for
other settings.
REFERENCE LEVEL ( )
Sets the standard input level.
Y �20dB/�18dB
22
LCT1424-001A_EN_p18-322211/4/03, 5:12 PM |
ACEC
