DT-V1910CG
17
AUTO 5-8ch 1-4ch 7-8ch 5-6ch 3-4ch
The tally lamp lights in green.The tally lamp lights in red.
The power supply starts approx. 1 second after the power switch is pressed.The power supply starts approx. 3.2 seconds after the power switch is pressed.1ch 2ch 3ch 4ch 1-2ch 3-4ch 1-4ch5ch 6ch 7ch 8ch 5-6ch 7-8ch 5-8ch1ch 2ch 3ch 4ch 5ch 6ch 7ch 8ch 1-2ch
The input video signal is synchronized with the built-in sync signal.The input video signal is synchronized with an external signal from an external sync terminal.
SYNC SELECTSynchronized signal selection.INT.:EXT.:RUSH DELAY TIMESets the time when the power supply to the monitor?s circuits (excluding the micro computers) starts after the power switch is pressed.STD.:SLOW:NOTE:If you are going to turn several Multi-Format Monitors on at the same time, it is recommended to apply SLOW to some of the monitors to control rush current.TALLY SELECTSelects the color of the tally lamp (when lit) on the upper front panel.GREEN:RED:REMOTE SYSTEMSelects the control system for the MAKE/TRIGGER terminals. Refer to How to use the MAKE/TRIGGER terminal on page 21.?MAKE (make contact)/ TRIGGER (trigger contact)E.AUDIO GROUPSelects the audio channel group for EMBEDDED AUDIO. It is displayed when an input card compliant with EMBEDDED AUDIO is installed.?1G/2G/1-2G1G:2G:1-2G:NOTE:The auto setting mixes and outputs all 8 signal channels. Sets the output level automatically by detecting the number of channels receiving the signal.* About sound output level Sound output level is set to a standard output level for all channels when several sound channels are output at the same time. The more channels are selected, the lower each channels level will be. (Each channel's level becomes half for 1 2 channel, 1/4 for 1 4 channel.)HOUR METER X100hDisplays the total usage time of the monitor in hundred-hour units.?000 ~ 655NOTES:?When the timer passes 655, it returns to 000.?The timer does not count the usage time under one hour.
ECT:
ADJUST:- + SELD1 SDI input card compatible with AUTO INPUT
MENU
<FUNCTION SETTING>COLOR SYSTEM:AUTO AUTO INPUT:ON SYNC SELECT:INT. RUSH DELAY TIME:STD. TALLY SELECT:GREEN REMOTE SYSTEM:MAKE E.AUDIO GROUP:1G HOUR METER X100h :000EXIT: SWITCHED OUTE.AUDIO SDI
SLOT2
IN1IN2
E.AUDIO
SLOT1INOUTHD SDI 1
button to
:Changes NTSC and PAL automatically.:Keeps the color system NTSC.:Keeps the color system PAL.AUTO INPUT is ON.AUTO INPUT does not function.
ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGSSLOT2 (both cards need to be compatible with AUTO INPUT), then connect the signal cable.card.
used.card compliant with AUTO INPUT is installed.)AUDIO. (When an input card compliant with EMBEDDED AUDIO is installed.)AUTONTSCPALON: OFF: used.when different signal cables are connected to each INPUT A and INPUT C and signals are input to the each of them.
Selects the control systems for the COLOR SYSTEM, synchronized signal, RUSH DELAY TIME, tally lamp colors, and MAKE/TRIGGER terminal.?Checks the amount of time that the monitor has been?Sets the AUTO INPUT function ON/OFF. (When an input?Selects the audio channel group for the EMBEDDEDPress the display the setting menu illustrated on the right.COLOR SYSTEMSelects the color system when using the video input card.NOTE:Normally select AUTO. However, if the input signal is unstable, select NTSC or PAL.AUTO INPUTWhen HD SDI signal and D1 SDI signal need to be switched to input accordingly by one signal cable, AUTO INPUT automatically detects whether a signal is being input to Input A (HD SDI input card) or Input C (SDI input card) and switches INPUT accordingly.NOTES: Functions only when input card compatible with AUTO INPUT is INPUT SELECT ERROR is displayed for approx. 3 secondsPreparation for the AUTO INPUT function (See below illustration)1. Insert HD SDI input card to SLOT1, and SDI input card to2. Input HD SDI signal or D1 SDI signal to HD SDI inputHD SDI input card compatible with AUTO INPUT
FUNCTION SETTING
buttons.
See page 12 for sub-menu and
Adjusts with and more information on Ťreset.
SELECT:SELECT:SELECT:SELECT:SELECT:24SELECT:
ADJUST:- +
Setting ItemsMENU
<FUNCTION SETTING>COLOR SYSTEM:AUTO AUTO INPUT:ON SYNC SELECT:INT. RUSH DELAY TIME:STD. TALLY SELECT:GREEN REMOTE SYSTEM:MAKE E.AUDIO GROUP:1G HOUR METER X100 :000EXIT:MENU ADJUST:- + <PICTURE SUB ADJ.>CONTRAST: 00 BRIGHT: 00 CHROMA: 00 PHASE: 00 NTSC SETUP: 00 COMPO.LEVEL: SMPTE sub menu resetEXIT:MENU ADJUST:- + <COLOR TEMP./BAL.>COLOR TEMP.: HIGH BLUE DRIVE: 000 RED DRIVE: 000 GREEN CUTOFF: 000 BLUE CUTOFF: 000 RED CUTOFF: 000 sub menu resetEXIT:MENU ADJUST:- + <SIZE/POSI. ADJ.>H.SIZE: 00 H.POSITION: 00 V.SIZE: 00 V.POSITION: 00 ZOOM H.SIZE: 00 ZOOM V.SIZE: 00 sub menu resetEXIT:MENU ADJUST:- + <DISTORTION ADJ.>PINCUSHION : 00 PIN.BALANCE : 00 PARALLELOGRAM : 00 TRAPEZOID : 00 ROTATION: 00 sub menu resetEXIT: <STATUS DISPLAY>STATUS DISPLAY :ON LEVEL METER ch :31BAR TYPE :3COLORS REFERENCE LEVEL :-20dB OVER LEVEL :-4dB BAR BRIGHTNESS :HIGHEXIT:MENU ADJUST:- +
press MENU.
* To go back the previous MENU,
.
Press
See page 20.
SELECT:
SETUP MENU
SETUP MENU SCREENS <SETUP MENU>FUNCTION SETTING PICTURE SUB ADJ. COLOR TEMP./BAL. SIZE/POSI.ADJ. DISTORTION ADJ. STATUS DISPLAY CONTROL LOCK :ON all resetEXIT:MENU ENTER:+
HOW TO USE SETUP MENU
16
(No.52097) |