DT-V1910CG
21
rs must beingle terminal to
the TRIGGER (trigger
r details.
GND of 15th terminal) the
front panel buttons.
3
RS-485 terminal >
2
MAKE/TRIGGER terminal >
1
6
7
tion (terminal open) of the controlled terminal.terminal) the controlled terminal.* MAKE or TRIGGER are selected from REMOTE SYSTEM in the setup menu.
5432114
15131211
1098
Control priority is in the following order; When trigger contact is on, the front panel buttons can be operated.
ABOUT EXTERNAL CONTROLHOW TO USE THE MAKE/TRIGGER TERMINAL
HOW TO USE EXTERNAL CONTROL1Turns on the tally lampOffOn*22Changes the input to INPUT AInvalidValid3Changes the input to INPUT BInvalidValid4Changes the input to INPUT CInvalidValid5Changes the input to INPUT DInvalidValid6Changes the input to INPUT EInvalidValid7Changes the input to INPUT FInvalidValid8COLOR OFFOffOn9AREA MARKEROffOn10ASPECTOffOn11TALLY SELECTGREENRED12AREA MARKER set-upwithout R-with R-*313STATUS DISPLAYONOFF14External ControlInvalidValid*215GNDcontrolled terminal.contact) system.(terminal open) of the controlled terminal.second) short-circuiting (short with GND of 15th terminal) the controlled terminal.disconnected.GND.
No.Functions to be controlledDisconnectionShort-circuiting*11. Short-circuit EXTERNAL CONTROL (14th terminal) to GND (15th terminal) to activate the external control.2. Under the MAKE system, controls each function by short-circuiting (short with GND of 15th terminal) or stable disconnection3. Under the TRIGGER (trigger contact) system, controls each function by Pulse Control, that is by instantaneously (approx. 1NOTES: When using INPUT A (the 2nd pin) through INPUT F (7th terminal), only the terminal in use should be short-circuited, the othe Under the TRIGGER system, multiple terminals cannot be short-circuited to GND (15th terminal). Be sure to short-circuit the s
*1:The TRIGGER (trigger contact) system switches each setting by instantaneously (approx. 1 second) short-circuiting (short with*2: TALLY (1st terminal) and EXTERNAL CONTROL (14th terminal) must be controlled with the MAKE (make contact) system even under*3: Activating each with R- or without R- setting in the AREA MARKER menu is possible. Refer to AREA MARKER on page 14 foOperation
The Multi-Format Monitor has two external control terminals.One is the MAKE/TRIGGER terminal, which allows the monitor to be controlled by the MAKE(make contact) or TRG. (trigger contact) method selected in the function setting.MAKE (make contact system):Controls functions either by short-circuiting (short with GND of 15th terminal) or stable disconnec-TRG. (trigger system): Controls the function by instantaneously (one second) short-circuiting (short with GND of 15thThe other terminal used for remote control is the RS-485 terminal, and this allows the monitor to be controlled by serial communication.NOTE:
button.
5 6 7 8
(cont'd)
[20dB/
buttons, then press
)
/
REFERENCE LEVEL 18dB] button.OVER LEVEL[8dB/6dB/4dB/2dB]
)4) is located next to CONTROL LOCK and
Audio channels and OVER/REFERENCE level indication
Brighter Darker1 2 3 4Enables normal operations.Invalidates all operations except the power switch and CONTROL LOCK.
AUDIO LEVEL METER display exampleLEVEL METER ch: 1-8, BAR TYPE: 3COLORS
Control lock on! warning to appear on the screen for approx.
HIGH:LOW:OFF:ON:operation except power switch and CONTROL LOCK causes the Ť3 seconds. (It is possible to operate the power switch and display SETUP MENU.)to ON, the cursor (cannot be moved. Select all reset by Confirmation message is displayed. To initialize, press To cancel the initialization, press the MENU button.
OVER LEVEL (Sets the input levels lower limit indicated in red for the 3COLORS display. -8dB/-6dB/-4dB/-2dBBAR BRIGHTNESS (Selects the brightness of the AUDIO LEVEL METER display.CONTROL LOCKInvalidates most of operations on the front panel (including menu screen operations).NOTES:?While CONTROL LOCK is set to ON, attempting to perform any?When SETUP MENU is displayed while CONTROL LOCK is setResets all SETUP MENU items to factory-preset values.1.2.
CONTROL LOCKall reset
SELECT:
ADJUST:- +
MENU
<STATUS DISPLAY>STATUS DISPLAY: ON LEVEL METER ch:3124 BAR TYPE :3COLORS REFERENCE LEVEL : -20dB OVER LEVEL : -4dB BAR BRIGHTNESS : HIGHEXIT:
)
White color display White (half transparent) display The audio level meter uses three different colors (red, yellow and green) to indicate variations in input levels.level set in OVER LEVEL.level set in REFERENCE LEVEL.exceed the level set in REFERENCE LEVEL.
button to
The information is displayed.The information is not displayed.
Red: displayed when the audio input exceeds theYellow: displayed when the audio input exceeds theGreen: displayed when the audio input does not
HOW TO USE SETUP MENU Sets the status display ON/OFF.* Switches the display on and off. Also selects the type ofdisplay. (When an input card compliant with AUDIO LEVEL METER is installed.)* Switches the AUDIO PLL setting. (When SDI input cardcompliant with EMBEDDED AUDIO is installed.)Press the display the setting menu illustrated on the right.NOTE: Function setting is displayedSTATUS DISPLAYSets the status display ON or OFF.when input card compliant with AUDIO LEVEL METER is installed.ON:OFF:LEVEL METER chSelects the audio channels used in the AUDIO LEVEL METER display. OFF/1:2/12:34/31:24/123:456/1-8NOTES: Numbers indicate the audio channel. The channel input levelindicated on the left side of : is displayed on the left side of the screen, and the channel input level indicated on the right side of : is displayed on the right side of the screen.? AUDIO LEVEL METER is not displayed when this is set to OFF.? When 1-8 is selected, the channel input level for 1,2,3 and 4 isdisplayed on the left side of the screen, and the channel input level for 5,6,7 and 8 is displayed on the right side of the screen.BAR TYPESelects the color of the audio level meter.WHITE-1:WHITE-2:3 COLORS:NOTES: For WHITE-1 and WHITE-2, the line indication for the standardinput level set in the REFERENCE LEVEL is displayed. Input level set in the OVER LEVEL is not displayed.? As for the audio channel bar display with no signal input, white isdisplayed for the 3COLORS setting, and gray is displayed for other settings.REFERENCE LEVEL(Sets the standard input level. 20dB/-18dB
STATUS DISPLAY
20
(No.52097) |