MasterPage: Advan_Right
GR-D231US.book Page 29 Wednesday, February 4, 2004 4:00 PM
MENUS FOR DETAILED ADJUSTMENTEN 29
WIDE MODEDEMO MODE
[OFF]: Records with no change in the screen ratio. For OFF: Automatic demonstration will not take place.
playback on a TV with a normal screen ratio.[ON]: Demonstrates certain functions such as Program
CINEMA*: Inserts black bands at the top and bottom AE with special effects, etc., and can be used to confirm
of the screen. The indicator appears. During playback how these functions operate. Demonstration starts in the
on wide-screen TVs, the black bands at the top and following cases:
bottom of the screen are cut and the screen ratio I When the Menu Screen is closed after ?DEMO MODE? is
becomes 16:9. When using this mode, refer to your wide-turned ?ON?.
screen TV?s instruction manual. During playback/I With ?DEMO MODE? set to ?ON?, if there is no operation for
recording on 4:3 TVs/LCD monitor/viewfinder, black about 3 minutes after the Power Switch is set to ?A? or ?M?.
bands are inserted at the top and bottom of the screen I Performing any operation during the demonstration stops
the demonstration temporarily. If no operation is performed
and the image appears like a letter boxed 16:9 movie.
SQUEEZE*: For playback on TVs with an aspect ratio for more than 3 minutes after that, the demonstration will
resume.
of 16:9. Naturally expands the image to fit the screen
without distortion. The indicator appears. When using NOTES:
this mode, refer to your wide-screen TV?s instruction I If a cassette is in the camcorder, the demonstration cannot
manual. During playback/recording on 4:3 TVs/LCD be turned on.
monitor/viewfinder, the image is elongated vertically.I ?DEMO MODE? remains ?ON? even if the camcorder power
D.WIDE*: The indicator appears. The zoom range is turned off.
is extended beyond the maximum optical zoom wide I If ?DEMO MODE? remains ?ON?, some functions will not be
angle range. This mode?s wide angle setting is equivalent available. After viewing demo, set to ?OFF?.
to using a 0.7X wide conversion lens. Zooming is
PRIORITY
possible from 0.7X to 10X. This mode is suitable for
shooting in a small room.[LCD]: The image is displayed on the LCD monitor when
* Available only when the VIDEO/MEMORY Switch is set to the viewfinder is pulled out while the LCD monitor is
?VIDEO?.opened.
FINDER: The image is displayed in the viewfinder when
WIND CUTthe viewfinder is pulled out while the LCD monitor is
[OFF]: Disengages the function.opened.
ON : Helps cut down on noise created by wind. The
CAM RESET
?? indicator appears. The quality of the sound will
change. This is normal.EXECUTE: Resets all settings to the factory-preset.
[RETURN]: Does not reset all settings to the factory-
SYSTEMpreset.
The ?s SYSTEM? functions which are set when the
CAMERA DISPLAY
Power Switch is set to ?M? are also applied when the
Power Switch is set to ?PLAY?.I The ?n? (CAMERA DISPLAY) settings are effective even
[ ] = Factory-preset when the Power Switch is set to ?A?. However, the menu
settings can be changed only when the Power Switch is set
BEEPto ?M?.
ADVANCED FEATURES
I The ?n? (CAMERA DISPLAY) settings except ?AUX MIC?
OFF: Even though not heard while shooting, shutter
are effective only for shooting.
sound is recorded on the tape.
[ ] = Factory-preset
BEEP: The beep sounds when the power is turned on or
off, and at the beginning and end of recording. It also ON SCREEN
activates the shutter sound effect. ( pg. 21, 32)
LCD: Keeps the camcorder?s display (except the date,
[MELODY]: Instead of a beep, a melody sounds when
time and time code) from appearing on the connected TV
any operation is performed. It also activates the shutter
screen.
sound effect. ( pg. 21, 32)
[LCD/TV]: Makes the camcorder?s display appear on
TALLYscreen when the camcorder is connected to a TV.
OFF: The tally lamp remains off at all times.DATE/TIME
[ON]: The tally lamp comes on to signal the start of
OFF: The date/time does not appear.
recording.
[AUTO]: Displays the date/time for approx. 5 seconds
REMOTE when the Power Switch is set from ?OFF? to ?A? or ?M?.
ON: The date/time is always displayed.
OFF: Disables the remote control operations.
I The date indication can also be turned on/off by pressing
[ON]: Enables the remote control operations.
the DISPLAY Button on the remote control.
( pg. 19, 37, 42) |
ACEC
