USING THE REMOTE CONTROL UNIT (GR-SXM745 only)
Make sure the remote control is pointed at the remote sensor p.
Playback Zoom5)To begin Insert Editing, press START/STOP P.
To magnify the recorded image up to 10X at anyWhen the counter reaches O0:00:00�, editing
stops automatically and the camcorder enters
time during playback. Make sure that the TBC
mode is activated.the Insert-Pause mode. To end Insert Editing,
press STOP U.
1)Press PLAY T to find the scene of interest.
YDuring Insert Editing, the original audio will be
2)Press ZOOM (T/W) R. Pressing T zooms in. To
heard from the speaker.
end zoom press and hold W until magnification
YAfter step 4), ORetake� ( pg. 13) can be
returns to normal. Or, press STOP U and then
performed.
press PLAY T.
YThe tape may stop slightly before or after the
YDue to digital image processing, the quality of the
designated end point, and noise bars may appear.
image may suffer.
Neither indicates a defect in the unit.
Animation And Time-Lapse
Audio Dubbing
The remote control lets you set/release interval
You can record a new soundtrack on a
time and recording time without setting REC TIME/
prerecorded tape (normal audio only). The sound
INT. TIME ( pg. 21) in SYSTEM MENU.
is recorded from the built-in microphone.
Animation
Perform steps 1) and 2) of the Insert Editing
Each time ANIM. O is pressed, the recording time
procedure.
changes in the following order: 1/4S, 1/2S, 1S, 5S
and no indication (off).3)Press REW Y to go a little beyond the beginning
of the scene onto which you want to dub the new
Time-Lapse
audio, press PLAY T to view the recorded tape,
Each time REC TIME O is pressed, the recording
then press PAUSE s at exactly the point where
time changes in the following order: 1/4S, 1/2S,
dubbing should start.
1S, 5S and no indication (off). Each time INT. TIME
4)While holding down A. DUB d, press and
f is pressed, the interval time changes in the
release PAUSE s.
following order: 15S, 30S, 1MIN, 5MIN and no
5)To begin Audio Dubbing, press PLAY T. When
indication (off).
the counter reaches O0:00:00�, Audio Dubbing
Insert Editingstops automatically and the camcorder enters
You can record a new scene onto a previouslythe Audio Dub-Standby mode. To end Audio
recorded tape. Only the video signal is recorded inDubbing, press STOP U.
this mode.YDo not press REW Y or FF a during Audio Dub-
1)Set the Power Switch @ to O�.Standby, or the edit points will not be accurate.
2)Play back the tape, locate the edit-out point andYIf the microphone is too close to the TV, or if the
press PAUSE s.Press and hold COUNTER R/MTVOs volume is too high, whistling or howling may
) for more than 1 second to reset the tapeoccur.
counter, then press it again for less than
For Insert Editing/Audio Dubbing
1 second so that OM� appears.
YInsert Editing and Audio Dubbing may not work
3)Press REW Y to go a little beyond the beginning
correctly if the tape contains blank segments, or if
of the scene you want to replace, press PLAY T
the recording speed was changed during the
to view the recorded tape, and press PAUSE s
original recording.
exactly at the edit-in point where the new scene
YTo edit/dub onto a tape, make sure the erase
should start.
protection tab is in the position that allows
4)While holding down INSERT I, press and
recording.
release PAUSE s. w appears.
YDo not press STOP U during Insert Editing or
Audio Dubbing, or the edit points will not be
accurate.
24
GR-SXM745/540U_EN2402.7.19, 9:25 AM |
ACEC
