Controls and indicators
DPC-981/782/781 (En/M)
Display
Card remote control unit (For DPC-782)
Shuffle mode indicator which lights whenWhen the card remote control unit is used, connect the AC
Lights in program mode.the shuffle mode is activated.adaptor or car battery adaptor to the main unit. The card
remote control unit cannot be used if the main unit is
Lights up when the HOLD switchB.BOOST indicator which lightspowered from batteries.
is set to the HOLD position.when Bass Boost is activated.
Battery duration indicator which lights
Displays the D.A.S.C. mode.D.A.S.C.PGMSHUFB.BOOST1 2Cduring recharging and blinks when the
The disc status is displayed.remaining battery power is low.
Stop/power off key76Play/pause key
At the time of D.A.S.C. ON, the re-Time/character information display
8 88888
sidual memory amount is displayed.Skip keys4c
Repeat mode indicator which lightsDisplays the track number.P.MODE/search keyREPEAT key
when one of the repeat modes isP.MODEREPEAT
activated.B.BOOST key
B.BOOST
VOLUMEVOLUME keys
REMOTE CONTROL UNITAfter setting the volume
RC-P800control of the main unit
LCD remote control unit(For availability of this accessory, refer to the Accessories table.)to the maximum
position, adjust the
listening volume with
these keys.
The keys with the same names as the keys on the main unitThe keys with the same names as the keys on the main unit
function the same as the keys on the main unit.function the same as the keys on the main unit.
Headphones jackOperating range (Approx.)
PHONESMain unit
HOLD switch
VOLUME controlSTB.BOOST1 2OOCThe operation keys of the remote
B.88BSKIPcontrol unit except for volume30u 30u3m
Bass Boost keycontrol are defeated.
STOP/OFFPLAY/PAUSE
Skip keysRemote
Stop/power off keycontrol unit
Play/pause key
To REMOTE/PHONES jack of the main unit.
Y When pressing several operation keys on the remote control
unit, leave an interval of more than 1 second between keys.
Y Always push in the headphone plug all the way before the power supply is switched ON.Y Erroneous operation may occur when the main unit is illumi-
Y When the headphone plug is inserted or pulled during playback, the operation of the unit and the liquid crystal display may not coincide.nated by direct sunlight or the light of a high-frequency lighting
(inverter) fluorescent lamp. In such a case, change the unit
In such a case, switch off the power supply once to make them coincide.
Y When the plug of the liquid crystal display remote control unit has been connected, the operation keys of the remote control unit may notposition to prevent erroneous operation.
be accepted. In such a case, disconnect the plug of the remote control unit once, wait for about 5 sec, and then connect it again.Y For battery replacement, use a commercially-available lithium
battery (CR2025).
Sound skip guard function (D.A.S.C.)In case of difficulty
What seems to be a serious trouble may sometimes be due to a simple mistake. Before calling for
* D.A.S.C. (Digital Anti Shock Circuit)service, check the items shown in the following table again. (If you request servicing due to the
reasons shown in the table, the service may be charged in some cases.)
It prevents sound skipping by storing the CDOs digital data in memory, and then playing backSymptomCauseRemedy
from the memory.
No operation occursY The HOLD switch is set to HOLD.Y Deactivate HOLD status.
when operation keys areY The batteries are exhausted.Y Replace all of the alkaline batteries,
pressed.or recharge the rechargeable batter-
Mechanism of D.A.S.C.ies.
Y The disc is placed upside down.Y Place the disc with the labeled side
D.A.S.C.D.A.S.C.D.A.S.C.up.
DisplayY Condensation has occurred insideY Leave the unit for about 1 hour be-
the unit.fore re-use.
CDY The AC adaptor or car battery adap-Y Connect it properly.
tor is disconnected.
No sound is heard fromY The headphones are connected in-Y Insert the plug securely into the
Storagethe headphones.completely.headphones jack.
of digitalY Adjust the volume on the main unit
Y The volume is set to the minimum
data
position on the main unit or remoteor remote control unit.
Digital memorycontrol unit.
Reproduced sound
Sound skips, or is inter-Y The D.A.S.C. is set to OOFF�.Y Set the D.A.S.C. to OON�.
Y In case of vibration above a certain degree, the memory data may be exhausted and the guard fromrupted.Y A strong vibration that exceeds theY Place the unit in a place not subject
sound skip may become temporarily ineffective.capacity of the D.A.S.C. has occurred.to vibration.
Y The disc is dirty.Y Clean it.
Y The lens is dirty.Y Clean it.
Y The headphone plug is dirty.Y Clean it.
Y The batteries are low.Y Replace or recharge the batteries.
Setting the D.A.S.C.
Noise interferes.Y The headphone plug is dirty.Y Clean it.
Y The batteries are low.Y Replace or recharge the batteries.
Each press changes the mode as follows.Y The headphones are connected in-Y Insert the plug securely into the head-
3completely.phones jack.
D.A.S.C1 D.A.S.C. HI
Digital data of about 20 seconds is stored in memory.
D.A.S.C.
This is the anti-shock play mode with a large vibra-Rechargeable batteriesY Commercially-available recharge-Y Use the special rechargeable
tion-resistance effect.HIcannot be recharged.able batteries are used.batteries (NB-130,NB-77 or NB-88).
Y Batteries have been inserted to theY Do not insert batteries to the O2
2 D.A.S.C. LOWO2 LONG PLAY� side.LONG PLAY� side.
GDigital data of about 6 seconds is stored in memory.
This mode provides a lower vibration resistance butD.A.S.C.For CHINA and Duty free shop in JAPAN
better sound quality than the D.A.S.C. Hi mode.LODigital recording is notY The D.A.S.C. function is ON.Y Please cancel the D.A.S.C. function.
possible for MD andY Batteries are used for playback.Y Please use a household power sup-
3 D.A.S.C. OFF (cancel)DAT.ply (AC adaptor).
When the player is used in a place free of vibration,
it is recommended to release the D.A.S.C. to ex-
tend the play time by reducing the battery powerOFF
consumption.
Notes :
1. This system uses a microcomputer so it may malfunction due to external noise or interference. In such
a case, unplug the power cord and remove the batteries, then plug the power cord again and insert the
batteries again.
Y The reproduced sound is interrupted during switching.2. Erroneous operation may occur when the headphone plug is plugged or unplugged; but this is not a
malfunction. |
ACEC
