Appendices
a aaaaaaaaaaaaaaaaaaaaaThe CX-3 will sound even when you press a key
Local Control On settinglightly. In other words on the CX-3, a note message
with fixed velocity will be transmitted when you
If you make connections as shown on the preceding
page, you must turn on the Echo Back setting of thepress a key lightly. However a note message with
velocity will not be transmitted until you press the
external MIDI sequencer or computer (so that the datakey all the way. This means that if you have made
it receives at MIDI IN will be retransmitted without
change from MIDI OUT), and turn off the Localsettings to transmit note messages with velocity, there
may be cases in which a note message is not transmit-
Control setting of the CX-3 (to disconnect the key-
board section from the tone generator section).ted even though the CX-3 has produced sound.
When you play the keyboard of the CX-3, the data will
be sent to the external MIDI sequencer or computer,
MIDI data dump
and will be echoed back to sound the tone generator
of the CX-3. In other words by turning the CX-3OsThe CX-3 can transmit its internal settings to a connected
Local Control off, you can prevent notes from beingMIDI data filer or to another CX-3 as exclusive data.
sounded in duplicate; once from the keyboard and
again from the echo-back.
Transmission
To turn off Local Control, set the Global mode Group 4
OMIDI Local� parameter to Off.While data is being transmitted, do not touch the
CX-3Os keys, drawbars, or knobs, and never turn off
If you are using the CX-3 by itself, you must turn
the power.
Local Control on. (If this is off, playing the CX-3OsThere are four types of data dump.
keyboard will produce no sound.)
Dump Program: Dump data for one program.
Dump All Programs: Dump all program data.
a aaaaaaaaaaaaaaaaaaaaa
Dump Global Parameter: Dump global data.
Connecting a MIDI keyboardDump All Programs and Global Parameter: Dump all
If you wish to use the CX-3 in Normal mode, and useprogram data and global data.
a MIDI keyboard connected to the MIDI IN connectorTransmitting a data dump
to play the CX-3Os Lower tone generator, you will
need to set the following parameters.1. Connect the MIDI OUT connector of the CX-3 to
Set the transmit channel of your MIDI keyboard tothe MIDI IN connector of the device that will
receive the data dump.
match the receive channel of the CX-3 (set by the
Global mode Group 2 OMIDI Lower Rx Ch� param-2. Enter Global mode.
eter). This allows your MIDI keyboard to be used as
The key LED will light.
the keyboard for the Lower tone generator.
3. While holding down the PROGRAM [7] key, press
If you also want to connect a sequencer, turn thethe [?] key six times.
Global mode Group 4 OMerge Lower Message�
parameter On. Channel messages of the channelThe display will indicate Dump Program.
When you select Dump Program, the number of the
specified by the OMIDI Lower Rx Ch� will be con-program to be dumped will be shown in the square
verted into the channel specified by the OMIDI Lower
Tx Ch� parameter, and transmitted.brackets [ ] at the right of the display.
If you wish to change the program, use the [�]/[+] keys.
The program transmitted here will be a program of
a aaaaaaaaaaaaaaaaaaaaathe mode that was last selected when you entered
Using a MIDI tone generator with velocityGlobal mode in step 2. If you wish to dump a Normal
mode program, select Normal mode before entering
The CX-3 is set to transmit note messages (with fixedGlobal mode in step 2. Similarly, if you wish to dump
velocity).
an EX mode program, select EX mode before entering
If you are using an external tone generator that isGlobal mode in step 2.
velocity-sensitive, you will need to set the following
parameters.After pressing the PROGRAM [7] key, you can press
the [?] from 6 to 9 times to select the following data
Set the Group 2 OMIDI Upper 2nd Ch� and OMIDIto dump.
Lower 2nd Ch� parameters to a setting other than Off.
With this setting, note messages with velocity will be[?] keyScreen displayDumped data
transmitted on the specified MIDI channel.Press 6 timesDump Programparameters for 1
program
However since this would cause two note messagesPress 7 timesDump All Programparameters for all
(with and without velocity) to be transmitted, turn theprograms
Global mode Group 2 OMIDI Upper Tx Ch� andPress 8 timesDump Globalglobal parameters
OMIDI Lower Tx Ch� parameters Off. Now the notePress 9 timesDump All Prog+Globalall program and
global parameters
messages with fixed velocity will not be transmitted.
As an alternative to the above setting, you can set the4. Press the [WRITE/ENTER] key.
OMIDI Upper 2nd Ch� and OMIDI Upper Tx Ch�The display will ask you to confirm the dump opera-
channel settings and the OMIDI Lower 2nd Ch� andtion.
OMIDI Lower Tx Ch� channel settings so that they do
not conflict, and set the receive channel of the con-
nected MIDI device so that it can receive note mes-
28sages with velocity. |
ACEC
