ENGLAND
- "
Starting up (engine start) must be carried out as described in detail under the heading
Before starting up check the oil and petrol levels.
?initial starting up?.
Do not smoke during the oil and petrol refuelling and checking operations.
Top up with petrol or oil if necessary (as described in detail in the previous
Never change gear while driving, the mower must always be at a standstill.
chapter).
Never mow the grass with reverse gear engaged.
#, "( -))+
Movement without power.
1. Position the gear level (11 pic I) to N (neutral). The mover can be
Only possible with the engine off.
moved and pushed without any problem.
Pushing the mower may be necessary to move it to the storage area.
Should it be necessary to manually move the mower the gear lever must be in the
neutral poistion 'X'.1. Position the hydrostatic gear block level (16 pic H3) on the discharge
Warning! For all manual shift operations the engine must be off and the ignition keyplate to neutral X. At the end of the manual push operation, reposition
removed.lever 16 to drive engagement pos. Y.
#- -( -))+
Ensure that there are no persons or animals within the operating vicinity of theTransmission occurs on the rear wheels by means of the hydrostatic gear, braking is
machine.by pressing the pedal (9) on the right of the steering wheel column.
Select the required speed and drive carefully. Transportation of other persons
is strictly forbidden.
#( -))+#
1. Press the brake pedal (9) which acts as a clutch, activate the1. Release the lever (10) and press the brake pedal (15) slowly fully down.
lever (11 pic I) according to chosen gear, then slowly release2. Advance speed may also be varied by manually operating the gas throttle lever (6 pic
pedal (9) until it starts up.To engage reverse gear, stop, and engage the reverseH1).
and engage the gear (11 pic I) into reverse (R) by pressing the brake pedal (9),
then slowly releasing the brake pedal (9) again.
2. Advance speed may also be varied by manually operating the gas throttle
lever (6 pic H1).
&( -))+&
Press the brake pedal (9 pic I1).Remove the right foot from the drive pedal (15 pic I1). Press the brake
To lock the brake pedal (9) use the lever (10).pedal (9). To activate the parking brake, pull the lever (10 pic I2) upwards.
Pressing by the brake, the drive pedal will automatically position itself on neutral.
" ,-#
The mower mechanism can only be switched on when the machine is at a standstill If possible, avoid driving at full throttle.
(parking brake engaged), with engine running, and throttle on (full) and with
operator seated on the mower.
,-( -))+3. It is possible to begin cutting in forward gear after having released the brake pedal.
1. Engage the brake (9)
2. Set the lever (12) on START positionIf the user stands up from the seat during the mowing, the engine switches off.
The mower mechanism is now engaged and the blade is rotating.
-, (( ,
Set the clutch blade lever (12) into STOP position.
The blade stops turning in about 5 seconds.
-
1)All persons operating the ride-on lawnmower must be familiar with the operatingImportant: remove the ignition key.
instructions.17)The engine must also be switched off:
Very important regulation: anybody under the age of 16 or under the effects of alcoholwhen you leave the machine or during its transportation
or medicines cannot operate the machine.before refuelling
2)Exhaust fumes from petrol engines: these fumes contain harmful carbon monoxide,during the grass collection bag emptying operations.
never operate the engine in closed environments.18)Take the greatest care during the cutter regulation operations. Risk of injury!! Keep
3)When operating on the ride-on lawnmower make sure that no other persons, especiallyfingers away from the area between cutter and bodywork. Wear gloves.
children or pets, are in the vicinity of the ride-on lawnmower.19)Only empty the petrol tank in the open.
4)Please ensure that foreign matters (strips, twigs, iron wire, etc.) are removed from the20)Before storing in a closed room, let the engine cool down.
lawn. Splinters can be hurled outwards or the blades can get damaged.21)In order to avoid risk of fire, the engine and exhaust must be kept free of grass, leaves
5)No smoking in the vicinity of the mower during operation.and leaking grease.
6)Only mow during daylight or under good lighting conditions.22)The grass collection bag must regularly be checked for signs of damage
7)Only Mow up or downwards a slope NEVER at an angle to the slope. Special care is23)Do not mow in reverse.
needed when changing direction on slopes.Maintenance and storage
1)Make sure that all nuts, bolts, and screws are kept well tightened to keep the mower in
8)When driving to the area to be mowed, the ride-on lawnmower mechanism must not
a safe operating condition.
be switched on.
2)Never leave the machine with fuel in the tank within an enclosed area where the fuel
9)Never use machine in the event of damage to the bodywork or without protective
vapours could reach naked flames or sparks.
equipment (i.e. grass collector bag, etc).3)Allow the engine to cool before storing in any enclosure.
10)The correct position of the engine block has been specifically designed and set at the4)Keep the engine, silencer, battery compartment and petrol tank free from grass, leaves
factory and must not be alteredand excess lubricant, in order to reduce the danger of fire.
11)Start by pressing the drive pedal with the greatest care, following the manufacturer?s5)Frequently check the grass bag for wear or deterioration
instructions. Pay attention to feet positioning at a sufficient distance from the cutting6)For safety reasons, be sure to replace worn-out or damaged parts in due time.
7)If the fuel tank has to be drained, it is essential that this be done outdoor.
blade.
8)Assemble the blades following the corresponding instructions and use only blades
12)Do not tilt the engine when departing and starting up.
bearing the maker's name or the trademark of the manufacturer or supplier and marked
13)This ride-on lawnmower has a safety device which switches off the engine every timewith the reference number.
that the operator leaves his seat.9)To protect hands during disassembly or assembly of the blades, it is absolutely essential
14)Keep your hands or feet away from the rotating blades. Stay away from the dischargeto wear suitable protective gloves.
opening whilst the blade are rotating.
15)Do not manually move or lift the machine with engine running.
16)In the event of engine blockage, clogging of the discharge channel and in all
maintenance operations on the cutter mechanism and in cases of temporary removal
of the safety protections the engine must be switched off and the cutter mechanism
disengaged.
17 |
ACEC
