Switching on and offPresetting stations
Switching onStations can be preset in three different ways:
If the TV set is cold and is placed in a warm room, wait
1. A.P.S. function (not available in a satellite mode)
for any condensation on the screen to evaporate before
Automatic Programme Selection.
switching the set on.
This function is executed automatically for the first time when
the TV set is installed and switched on.
Switch the TV set on by pressing the main switch.
2. Station search
The TV set is now in standby mode, indicated by a red light.3. Direct channel input
Single-digit programme positions can be selected with the numeri-Direct input of the frequency in satellite mode
cal keys a b c . . . or with the keys Pg or Ph on the remote
control or with the - P + keys on the TV set
1. A.P.S. function
When the TV set is on, two-digit programme positions can be selec-When the TV set is switched on for the first time, the following mes-
ted by pressing the preselection key for two-digit input, followed bysage is displayed on the screen in terrestrial mode:
the numerical keys.
A.P.S.
PLEASE, CHECK ANTENNA CABLE
A TV set which is equipped with a satellite receiver module has
}AUTO. PROGRAMMING SYSTEM
three operating modes:
ESTART
a) TV mode for terrestrial stations received via an antenna orTVCANCEL
cable,
This function can be cancelled by pressing the x key.
b) TV mode for satellite stations,
The A.P.S. function is started by pressing the e key.
}
c) satellite radio mode (FM and ADR)The TV set now searches the entire terrestrial reception range (recei-
ved with an antenna or from cable) for stations.
When the TV set is switched on, it is always in terrestrial mode.
After the search has been completed, the station table is displayed
On TV sets retrofitted with a satellite module, the power-on rou-
on the screen. This could, for example, look like this:
tine can be modified so that satellite TV or satellite radio mode is
always selected when the set is switched on. To do this, you
}must open the menu aSERV.O:PROGRAMM
Y Press the M key to open the main menu aMENUO.00 ----10 C-1620 ----
01 ARD11 C-5221 ----
Y Press the numerical keys 6 0 8 6.02 ZDF12 S-0122 ----
03 BR 313 S-0623 ----
Y The menu aSERV.O is displayed on the screen
04 RTL14 S-1624 ----
05 RTL215 ----25 ----
SERV.06 SAT116 ----26 ----
}
07 PRO717 ----27 ----
TURKISH08 NDR18 ----28 ----
DEFAULT09 MDR19 ----29 ----
SELECTDELETE
TV
INSERTAUTOSTORE
Y Press the key Ph to select aDEFAULTO..
In some cases, the station logos may not be recognised during the
}
Y Select the desired operating mode with the keys f / e:.
station search. In this case, you can enter the station a
G
TV = errestrial station received via antenna or cable;
logo as described on page 34.PG
SAT = atellite station received via satellite dish;.G
P
G
RAD = radio station (FM and ADR) received via satellite dishThe various programme positions in the station
The TV set switches to the mode selected here when it istable can be selected with the cursor keys.
switched on.
You can then do the following with the selected
When the TV set is on, you can switch between the operating
}programme position:
modes with the key # . The current operating mode is indicated
by the colour of the logo displayed on the screen: blue = terre-
SELECT =pressing the red key selects this programme position
strial mode, yellow = satellite TV, green = satellite radio.
INSERT = the programme position selected with the red key
can be inserted in another position in the table
Switching offDELETE = deletes the programme position
Pressing the OFF key on the remote control switches the TV set toAUTOSTORE = calls the A.P.S. function (not possible for satellite
standby mode. Pressing the main switch on the TV set switches thestations)
set off completely.Y Close the menu by pressing the TV key.
33 |
ACEC
