AG-3200P-EN-1.fm Page 13 Tuesday, May 28, 2002 2:54 PM
DPress TIMER. The VCR turns off automatically and ?#? is DCancel or change program setting
displayed on the display panel.To cancel a program, press CANCEL when the Program screen
you do not want is shown.
To change a program, press the appropriate button: START+/-,
24HR Quick Programing
STOP+/-, DATE+/-, CH+/-, DAILY (M-F) (Number key ?8?),
You can program a timer recording that starts within 24 hours
WEEKLY (Number key ?9?), and/or SP/EP when the Program
using the JOG dial on the VCR.
screen on which you want to make changes is shown.
Load a cassette with the record safety tab intact. The VCR turns
on, and the counter is reset, automatically.EReturn to normal screen
Press PROG. CHECK repeatedly until no Program screen is
APress 24HR QUICK PROGRAM on the VCR.
shown.
?$? starts blinking on the display panel.
BTurn the JOG dial to the left or right to set FReengage timer recording standby mode
Start time
the start time.Press TIMER. The VCR turns off automatically and ?#? is
I One click stop of the JOG dial changes displayed on the display panel.
the time in 5-minute intervals.I When ?AUTO TIMER? is set to ?ON? ( pg. 15), the timer
CPush the JOG dial. ?? starts blinking on recording standby mode automatically resumes when you turn Stop time
the display panel. Turn the JOG dial to the off the VCR.
left or right to set the stop time.
I To set the tape speed, press SP/EP. The
Program overlap warning display
current setting for the tape speed appears Channel number
If ?PROGRAM NOT COMPLETED PROGRAM OVERLAP?
on the display panel for about 5 seconds.
Press SP/EP again to change the setting appears, you have another program overlapping the program you
have just made. The Program Check screen appears and
while tape speed is displayed.
conflicting programs will start blinking.
DPush the JOG dial. Turn the JOG dial to the
PR START STOP CH DATE
left or right to select the channel, then press 24HR QUICK 1 8:00P 10:00 12 12/24
PROGRAM. The VCR turns off automatically and ?#? is PROGRAM NOT COMPLETED2 10:00A 10:45 40 12/25
3 11:30P 1:00 12512/25
displayed on the display panel. PROGRAM OVERLAP49:00P 10:00 1012/24
5
6
NOTES:7
8
I If ?Err? appears on the display panel, repeat the above steps
( , ) THEN ( ) (PROG.) : END
again.
Example:
I When a menu screen is shown, you cannot use 24HR Quick
Program 1 (you have just made) and Program 4 overlap each other
Programing function. Press MENU to return to normal screen,
and try again.
ASelect program to modifyPR START STOP CH DATE
I You can use 24HR Quick Programing function also when the 1 8:00P 10:00 12 12/24
Press rt, then press OK or e.2 10:00A 10:45 40 12/25
VCR is turned off.3 11:30P 1:00 12512/25
I You can only select one of the 49:00P 10:00 1012/24
I For 24HR Quick Programing function, the program overlap 5
overlapping programs.
warning display does not appear even if some programs overlap 67
I If you do not mind this overlap, press
each other.8
PROG. to finish the timer program ( , ) THEN ( ) (PROG.) : END
setting. The program starting earlier or
To use the VCR while it is in timer recording standby program with the lower program number will be recorded.
modeBCancel or change program settingPROGRAM 4
Press TIMER, then press POWER 1. After you use the VCR, press To cancel a program, press CANCEL when STARTSTOP
9:00PM10:00PM
TIMER again to put the VCR into timer recording standby mode.the Program screen you do not want is DATECH
12/24/0210 SP
shown.TUE
To change a program, press the PRESS (CANCEL) TO CANCEL
Checking, canceling or changing program settingsappropriate button: START+/-, STOP+/-, PRESS (OK) TO CONFIRMPRESS (PROG.) TO END
DATE+/-, CH+/-, DAILY (M-F) (Number
ADisengage timer
key ?8?), WEEKLY (Number key ?9?) and/or SP/EP when the
Press TIMER, then press POWER 1.Program screen on which you want to make changes is shown,
I When ?AUTO TIMER? is set to ?ON? ( pg. 15), you do not then press OK or e.
have to press TIMER.I If the overlap is not yet solved, the conflicting programs will be
shown on the Program check screen. Repeat the above steps
BAccess Program Check screenPR START STOP CH DATE
1 8:00P 10:00 12 12/24again.
Press PROG. CHECK.2 10:00A 10:45 40 12/25
3 11:30P 1:00 12512/25
4
CAccess Program screen5
6
Press PROG. CHECK again. Each time you 7
8
press PROG. CHECK, the next program?s PRESS (CHECK) TO NEXT
Program screen appears.
? 13 ?
Page 13May 28, 2002 2:53 pm |
ACEC
