Setting menus
OTHER FUNCTIONS screen
Item/Item/
Description of settingsDescription of settings
(display mode)(display mode)
REMOTEFor setting the operations which areBEEP SOUNDFor setting the beep tone to ON or OFF.
(Camera)performed using the accessory wireless(Camera)OFFON
(VCR)remote control unit. (See page 20 for the
remote control unit settings.)When ON is selected as the setting, the
VCR1: The operation performed by thebeep tone is sounded at the times given
remote control unit which has been setbelow.
to be used for VCR1 are accepted.O When the beep tone is sounded, the
VCR2: The operation performed by theaudio signals from the output connectors
remote control unit which has been setare muted, and the beep tone is output
to be used for VCR2 are accepted.instead.
OFF: Operations performed by the remote[Beep tone sounds once]
control unit are not accepted.OWhen the POWER switch has been set
to ON
DV CONTROLFor setting the control method when
OWhen shooting has commenced
(Camera)backup shooting is to be performed by
[Beep tone sounds twice]
connecting a component for backup
OWhen shooting has been temporarily
purposes to the DV connector.
stopped
OFF: The component for backup purposes
[Beep tone sounds 10 times]
is not controlled.
OWhen the cassette tape has not been
EXT: The component for backup purposes
inserted
is controlled using the START/STOP
OWhen the cassette tape is in the
button on the camera recorder. The
recording pause mode
images shot by the camera recorder are
recorded by the component for backupOWhen condensation has formed inside
the camera recorder
purposes.
OWhen a problem has occurred in the
However, the camera recorder does not
camera recorder
record the images.
BOTH: The images shot by the cameraCLOCK SETFor setting the internal calendar of the
recorder are recorded by both camera(Camera)camera recorder.
recorder and the component for backup(VCR)
purposes.
TIME SHIFTFor adding the time which was set using
CHAIN: When the tape in the camera
(Camera)this item to the time of the internal calendar
recorder approaches the end during
(VCR)(to compensate for time differences) for
shooting, recording is automatically
display in the viewfinder and on the LCD
commenced by the component for
monitor. The clock time after the
backup purposes, which has been set to
compensation is also recorded on the tape.
the recording standby mode.
+23h --- +1h, OFF, �1h --- �23h
DV CMD SELFor setting the recording operation to be(In 1-hour increments)
(Camera)performed by the component for backup
TAPE PROTECTWhen the camera recorder is left on
purposes when the START/STOP button
(Camera)standby for about 5 minutes in the shooting
on the camera recorder has been pressed.
pause mode, it is automatically set to the
REC_P:
tape protection mode. Which tape
The mode is switched between recording
protection mode is to be established is
and recording pause.
selected using this item.
STOP:
POWEROFF: The camera recorderOs power is
The mode is switched between recording
set to the OFF mode.
and stop.
STBY: The cylinder head is set to the stop
<Note>
mode.
Select STOP as the itemOs setting if the
component for backup purposes is notUSER FILELOAD: The settings stored last in the user
equipped with a recording pause function.(Camera)file are loaded.
(VCR)SAVE: The user file settings which have
REC LAMPFor setting the lighting of the tally lamps.
been changed are saved.
(Camera)OFF: The tally lamps do not light.
INITIAL: The user file settings are restored
FRONT: The front tally lamp (by the
to the factory settings.
microphone) lights.
O When the LOAD or INITIAL operation
REAR: The rear tally lamp (by the
has been performed, set the POWER
viewfinder) lights.
switch on the camera recorder to OFF
BOTH: Both the front and rear tally lamps
and then to ON again in order to enable
light.
the settings.
HOUR METERFor indicating the total rotational time of the
(Camera)cylinder head (5-digit display in 1-hour
(VCR)increments).
The underlining indicates the factory setting.
46 |
ACEC
