Setup menus
<OPERATION>(continued)
No./ItemDescription of settingNo./ItemDescription of setting
112For selecting what playback images are to 113*be1For selecting whether to allow or inhibit recording
output in the STANDBY OFF mode and EJECTon the cassette tape.
FRZ MODEmode.REC INH0000OFF:
SEL0000DIS:Recording on the cassette tape is enabled when the
The video output is muted.cassettes accidental erasure prevention mechanism
0001 STB OFF:has been set to the recording enable position.
Only when the STANDBY OFF mode is0001ALL:
established is the image which was beingAll recording on the cassette tape is inhibited.
played back at that moment frozen and output.0002PRE:
0002 SOF&EJ:Overwriting is inhibited during normal recording.
When either the STANDBY OFF mode or theThis is the setting to activate the accidental erasure
EJECT mode is established, the image whichprevention function. While CTL is detected, the
was being played back at that moment isrecording is inhibited, and when CTL cannot be
frozen and output.detected, it is executed.
<Notes>0003 NORM :
" The status when the picture is frozen is determinedNormal recording is inhibited.
by the setup menu item No.604 (FREEZE SEL)
Use this setting when it is preferable to avoid
setting.
using normal recording in all applications
" In the EJECT mode, the frozen picture is output only
except for editing.
when 1 (BLACK) or 2 (GRAY) has been selected as
0004V/CTL:
the setup menu item No.106 (EJECT EE SEL)
setting.The recording of the video and CTL signals is
" The picture freeze is forcibly released if a change hasinhibited.
occurred in the output format of the HD serial outputUse this setting when it is preferable to avoid editing
signals when operation has transferred to the EJECTin all applications except for audio editing.
mode.<Note>
When the PRE, NORM or V/CTL setting has been
selected, the REC INHIBIT lamp blinks (on for approx.
0.5 sec. and then off for approx. 0.5 sec.).
Description of MEMORY STOP function
114For selecting whether the REC INHIBIT lamp is to
blink or light when the cassette tape has been set
The MEMORY STOP function does
not work if this margin is less REC INHthanto the accidental erasure protection mode.
0 point d2 frames. LAMP0000 LIGHT: The lamp lights.
0001 FLASH: The lamp blinks.
<Note>
3REW1FFIf 1 (ALL) has been selected as the setup menu item
buttonbuttonNo.113 (REC INH) setting, the REC INHIBIT lamp will
be lighted at all times regardless of the REC INH LAMP
4FF2REWsetting.
buttonbutton1
115*For selecting whether to enable or disable the
operation of the EJECT button on the VTRs
EJECT SWfront panel.
! If the FF button is pressed, the normal FF operation INHis performed0000REC : Operation is disabled while the
since there is no 0 point in the direction of this operation.VTR is in the recording mode.
0001OFF: Operation is enabled in all
@ If the REW button is pressed, the PREROLL lamp lights (as doesmodes.
the SHTL lamp), the VTR prerolls the tape, and it automatically
stops when the counter value is at the 0 position.
Accidental erasure protection function
This function is used to prevent parts already recorded on a tape from being
# If the REW button is pressed, the normal REW operation is
recorded over. Accidental erasure of pre-recorded tapes is prevented by
performed since there is no 0 point in the direction of thispositioning the CTL signal rec/play heads as shown in the figure below so that
operation.whether a recording has been made can be determined by the presence or
absence of the CTL signal. When the REC/PLAY button is pressed with a pre-
$ If the FF button is pressed, the PREROLL lamp lights recorded (as tape, doesthe tape runs but the REC button lamp blinks, the beeping
the SHTL lamp), the VTR prerolls the tape, and it alarm is sounded, and no signals are recorded.automatically
stops when the counter value is at the 0 position.
A/C heads
(rec/play heads)
*1: This item is not displayed when the 23/24 Hz or 25 Hz (HD or
PRE CTL
SD) mode has been selected as the system menu item No.25head
(SYSTEM FREQ) setting.
The underlining (__) denotes the factory setting mode.Rough sketch showing CTL head positions
85 |
ACEC
