Operation
When component signals are used9. Turn the menu setting control (main), and set it so that
the following item appears on the LCD panel.
1. Select the pan-tilt head system using the
CCAABBLLEE CCOOMMPP MMAANNUUAALL
CONTROL/PREVIEW MONITOR OUT SEL button.
ff RReessppoonnssee :: 00
2. Connect a waveform monitor to the VIDEO/Y OUT<Note>
connector on the main unit corresponding to the pan-tiltWhen component signals have been set as the video
head system currently selected.input signals, the output signals from the convertible
camera will be switched to Y/C signals, and
3. Press the MODE button to establish the BAR mode andchrominance signals will be output from the Pr OUT
switch the output signals from the convertible camera toconnector. When another item on the menu is selected,
color bar signals.the output signals will be switched to the component
signals.
4. Press the MENU button, turn the menu setting control
(main), and set it so that the CABLE COMP item10. Adjust the frequency response using the menu setting
appears at the top of the LCD panel.control (R) in such a way that the burst level appearing
on the waveform monitor is set to 40 IRE (0.286V).
CCAABBLLEE CCOOMMPP
Repeatedly adjust the luminance signal and frequency
nOOKK KKeeyy
response until the signal waveforms shown below are
5. Press the OK button.matched.
The following item appears on the LCD panel.<Note>
In the luminance and chrominance signal adjustments
CCAABBLLEE CCOOMMPP AAUUTTOO
performed by the multi-function controller, the level
SSTTAARRTT?? n OOKK KKeeyy
cannot be reduced below the level of the input signals
6. Turn the menu setting control (main), and set it so thatfrom the camera.
the following item appears on the LCD panel.It may not be possible to perform these adjustments if
the length of the cables from the pan-tilt heads to the
CCAABBLLEE CCOOMMPP MMAANNUUAALL
main unit of the multi-function controller is too short.
YY LLeevveell :: 00
IRE
<Note>
100
When composite signals have been set as the video90
output signals, the video output signals will be switched80
70
to component signals.
60
When another item on the menu is selected, the output50
signals will be switched to the composite signals.40
30
20+20+20
7. Adjust the luminance signal using the menu setting10
040 IRE
control (R) in such a way that the level of the white area
�10(0.286 V)
appearing on the waveform monitor is set to 100 IRE�20
�20�20
(0.714V).�30
�40
IRE
100+100Waveform monitor
90
8011. Select the next pan-tilt head system using the
70100 IRE
CONTROL/PREVIEW MONITOR OUT SEL button, and
60(0.714 V)
50continue adjusting the cable compensation in each
40system concerned.
30
20
10+7.54Y6Y9
05
�1037Y10 41
�20
�30OPERATEOPENTELEFARGAINAUTOBALIRISZOOM FOCUSAWCCONTRASTWHITELCDLAMPDEFWIPH/FEXTNDOPTIONCAMERA CONTROLPAN/TILT SET
ONA
�40MANU
MODEBARNGTRACING MEMORY
OFFCAMBOKR/BSTART
INCOMDATA SETABCATWCONTRCAMERAOLGAIN/PEDMENUOKPOINTSTART/STOPRESTORERESET
Waveform monitorTRACING/PRESET MEMORYTALLY
CALLTR/PSET M.LOCK12345678910PRIORITY
CLOSEWIDENEAR12345AUX
LEVELCONTROL/PREVIEW MONITOR OUT SEL
IRISTRPSETTELEMEMORY11121314151617181920SPEEDUP
8. Connect the VIDEO/Y OUT connector on the main unitAUTO
LOCKEMPTYFULLMANULOHIGHW
to the external reference input connector on theIRIS212223242526272829130IRIS
FOCUSFOCUS
waveform monitor, and connect the Pr OUT connector31323334353637383940LR
on the main unit to the video signal input connector on
CLOSENEARWIDEOPENFAR41424344454647484950CLOSENEARDOWNOPENFAR
the waveform monitor.ZOOM/FOCUS/IRISPAN/TILT/FOCUS/IRIS
LIMITONLIMITOFF
24 |
ACEC
