7540en.fm 23 23777
? e9�79â 1
+ To change a programme
To record programmes from satellite
Press [3 , 4 ] to select the programme and press [ENTER].
receiver by RGB signals(!page 22, step 3)
Preparation+ To delete a programme
eChange the settings in the SETUP menu as follows (!page 41).Press [3 , 4 ] to select the programme and press [c CANCEL].
-?AV2 Input?: ?RGB (Not NTSC)?
+ To exit the timer recording list
-?AV2 Connection?: ?Normal?
Press [PROG/CHECK].
Follow the steps indicated for manually
+ To put the unit on timer recording standby
programming timer recordings Press [F TIMER].
The unit turns off and ?F ? lights on the unit?s display to indicate timer
(!page 22).
recording standby has been activated.
eMake sure you connect to the ?TV Scart terminal? of a Sky Digital
STB with a 21-pin Scart lead.
eProgrammes that failed to record are displayed gray. They are
eSet your Sky Digital STB to output ?RGB? signals.
automatically deleted from the timer recording list at 4 a.m. two
eAfter setting the Personal Planner programmes as required, Sky
days later.
Digital STB must be left on (not set to standby) to ensure
continuous output of RGB signals.
Linked timer recordings with external
equipment (EXT LINK)
Check, change or delete a programme
[RAM] [DVD-R]
eEven when the unit is turned off, you can display the timer
If an external equipment (for example a satellite receiver) with a
recording list by pressing [PROG/CHECK].Recording
timer function is connected to the AV2 terminal of this unit by a
21-pin Scart lead (!page 7, 10), it is possible to control the
Press [PROG/CHECK].recording of the unit with the equipment.
Preparation
IconseChange the ?Ext Link? in the SETUP menu to match the connected
[ This programme is currently recording.equipment (!page 41).
W The times overlap those in another programme. eTimer programming has to be done on the external equipment and
Recording of the programme with the later start time switch to the timer recording standby mode. Refer to the
equipment?s operating instructions.
starts when the earlier programme finishes recording.
F The disc was full so the programme failed to record.Press [EXT LINK].
The material was copy-protected so it was not recorded.The unit turns off and switches to the recording standby mode.
eRecording begins when a signal is received from the connected
X The programme did not complete recording because the
equipment.
disc is dirty or some other reason.
eAs long as a video picture is being transmitted by the external
equipment, the unit will record it.
When the following message appears on the television screen, press
[2 , 1 ] to select ?Yes? (continue recording the current programme)
or ?Cancel? (cancel recording) and press [ENTER].
DVD now recording this programme.
TIMER
Remain1:58 SP
RECORDING12:56:00 15. 7. TUEYesCancel
No. NameDateStart Stop ModeDisc PDC space
New Timer Programme
ENTERRETURN
[Note]
It is not possible to use EXT LINK function for timer recording of
RGB signals from Sky Digital STB (!left, To record programmes
SELECTfrom satellite receiver by RGB signals).
Press ENTER to store
ENTERRETURNnew programme.
To record programmes from a satellite receiver
using the ?Sky Personal Planner? function
Change the settings in the SETUP menu as follows ( !page 41).
Message displayed in the ?Disc space? line-?AV2 Input?: ?Video?
-?AV2 Connection?: ?Normal?
OK:Displayed if the recording can fit in the -?Ext Link?: ?Ext Link 1?
remaining space.eMake sure you connect to the ?VCR Scart terminal? of a Sky Digital
> (Date): For recordings made daily or weekly, the display STB with a 21-pin Scart lead.
will show until when recordings can be made (up
to a maximum of one month from the present To cancel the external control
time) based on the time remaining on the disc.Press [EXT LINK] to stop recording or to cancel linked timer
! : It may not be possible to record because:recording standby.
ethe disc is write-protectedeYou can also press and hold [+ ] on the main unit for more than 3
seconds to stop recording.ethere is not enough space left
eIn order to prevent accidental operation, press [EXT LINK] to
ethe number of possible titles has reached its
cancel the setting after recording is finished.
maximum.
For your reference
eThe video being recorded automatically appears on the television
when connected to this unit?s AV1 terminal with the 21-pin Scart
lead.
eThis function does not work with some equipment. Refer to the
equipment?s operating instructions.
eThe beginnings of recordings may not be recorded correctly in
some cases.RQT7540
eWhen ?Ext Link? is set to ?Ext Link 2?, this function does not work if
23the input signal is NTSC system. |
ACEC
