1@&4@@@&6�?´
Before useREAD ALL INSTRUCTIONS BE-It shows the remaining battery ca-[for ES8161]
FORE USE.pacity from 0% to 100%, in 10% in-The charge status lamp will glow
This Wet/Dry shaver can be used for
crements.when the shaver is being charged. It
wet shaving with shaving lather or for
ChargingWhen the charging is completed, itwill blink when the charging is com-
dry shaving. You can use this water-
Connect the power cord to thewill indicate �100%� and the backlightpleted (see fig. 2 (F)).
tight shaver in the shower and clean
shaver, and plug the adaptor to anof LCD display will flash once inYou can fully charge the shaver in 1
it in water. Treat yourself to wet lather
AC outlet. (see fig. 1 (A))about 1 second. It will flash once inhour if the low battery indicator blinks
shaves for at least three weeks and
The shaver will be adjusted automati-about 2 seconds for 10 minutes af-(see fig. 2 (E)).
notice the difference. Your Panasonic
cally to voltages between 100-240Vter charging is completed (see fig. 2The unit can be used once or twice
Wet/Dry shaver requires a little time
AC.(B)).more after the low battery indicator
to get used to because your skin and
In some areas, a special plug adap-You can fully charge the shaver in 1starts to blink.
beard need about a month to adjust
tor may be required.hour if the LCD display shows 10%
to any new shaving method.
and lower.A full charge will supply enough
� When charging the shaver for the
Parts identificationThe plug symbol blinks in the LCDpower for approx. 14 shaves (3 min-
first time or when it has not been indisplay when the remaining batteryutes per shave for a normal beard).
(see fig. 1)
use for more than 6 months, thecapacity is 10% and less.Before travelling, charge it fully for 1
A Protective capplug symbol and backlight of LCD
The unit can be used once or twicehour if you will not be taking the adap-
B System outer foildisplay (ES8163) or charge statusmore after the LCD display starts totor with you.
lamp (ES8162, ES8161) may notshow 10%. (Differs depending on theIn case your shaver is without charge,
C Inner blades
illuminate for a few minutes afteruse situation.)you may quick charge it for 1 shave
D System outer foil release buttonsoperation. These lights will eventu-
in about 5 minutes.
E Pivot action selectorally illuminate if kept connected.[for ES8162]
The charge status lamp will glowCharge with charging
F LCD display [ES8163]
Adequate ambient temperature forwhen the shaver is being charged.
LED display [ES8162]stand
charging is between 15 to 35 °C.100 to 20 of the battery capacity
[ES8161](see fig. 1 (B))
� If it is far below or over the appro-monitor will all illuminate and the
To charge with the charging stand,
G Battery capacity monitorpriate temperature, the charging
charge status lamp will blink after
connect the power cord to the charg-
H Charge status lamptime may extend, or the adaptorcharging is completed (see fig. 2 (C)).ing stand. Place the shaver into the
may not function.10 minutes after charging is com-
I Low battery indicatorstand, and plug the adaptor to the
� In particular, low temperature maypleted, the battery capacity monitor
AC outlet.
J On/Off switchshorten the life span of the re-
will extinguish and the charge status
You can always store your shaver in
K Finger restchargeable battery, In this case, thelamp will continue to blink (see fig. 2the charging stand to maintain full
backlight of LCD display (ES8163)(D)).
L Trimmerbattery capacity. This shaver cannot
or charge status lamp (ES8162,You can fully charge the shaver in 1
be overcharged.
M Trimmer handleES8161) blinks twice in 1 second.
hour if the LED display shows 20%.
N AdaptorThe battery capacity monitor indi-
[for ES8163]cates the charge remaining in the
O Power cord
When the shaver is being charged,battery. The unit can be used once
P Charging standthe backlight of LCD display turns
or twice more after the �20� starts to
Q Cleaning brushon, and the plug symbol appearsblink. (Differs depending on the use
(see fig. 2 (A)).situation.)
R Soft case
67
78 |
ACEC
