Glossary
CAM and Smart Card : A CAM (conditionalSystem :Analogue programmes are not broadcast in
access module) and a smart card can bethe same way in all countries.There are different
connected to the television.This unit allows youstandards:BG,DK,I,and L LO.The SYSTEM setting
to access subscription digital channels or special(p.9) is used to select these different standards.This
services from the provider.is not to be confused with PAL or SECAM colour
Digital receiver : The television is equiped with ancoding.Pal is used in the majority of European
integrated digital tuner which enables you tocountries,Secam in France,Russia and the majority
receive a digital transmission with a terrestrialof African countries.The United States and Japan use
antenna.The tuner is able to received Digital Videoa different system called NTSC.The inputs EXT1 and
Broadcast compliant with MPEG-2,up to MainEXT2 are used to read NTSC coded recordings.
profile @ Main level.16:9 : Refers to the ration between the length and
EasyLink : Digital link between the set and theheight of the screen.Wide screen televisions
video recorder which allows a direct transfer ofhave a ration of 16/9, conventional screen TV
certain information such as channel setting.sets have a ration of 4/3.
Tips
Poor reception (in analogue mode)key:S-VHS2 (S-VHS3) instead of EXT2 (EXT3).To
The proximity of mountains or high buildingsplay a video cassette,check that it has been recorded
may be responsible for ghost pictures, echoingunder the same standard (PAL,SECAM,NTSC)
or shadows. In this case, try manually adjustingwhich can be replayed by the video recorder.
your picture: see "fine tuning" (p.12) or modifyNo sound (in analogue mode)
the orientation of the outside aerial. Does yourIf on certain channels you receive a picture but no
antenna enable you to receive broadcasts insound,this means that you do not have the correct
this frequency range (UHF or VHF band)? TV system.Modify the SYSTEM setting (p.9).
In the event of difficult reception (snowyThe remote control no longer works.
picture) switch the NR on the PICTURECheck that the mode selector on the side of
analogue menu to ON.(p. 13).the remote control is set to TV.
Bad picture (in digital mode)The TV set does not react to the remote
If the picture freezes a lot,or in cases of blockcontrol; the indicator on the set no longer
effect,there is a problem of poor reception.Pleaseflashes when you use the remote control?
check with the signal strength menu (see p.6).Replace the batteries.
Depending on the strength of digital terrestrialStandby
signals available in your area, standard aerialsWhen you switch the TV set on it remains in
used for analogue transmissions will in moststandby mode and the indication LOCKED is
cases provide satisfactory reception of digitaldisplayed when you use the keys on the TV set?
signals. If it is not the case, a good qualityThe CHILD LOCK function is switched on (p.14).
narrow beam antenna should be professionallyIf the set receives no signal for 15 mins, it
installed outside the property and aligned toautomatically goes into standby mode.
capture the maximum digital signal strength.To save power,your set is fitted with components
No picturethat give it a very low power consumption when in
Have you connected the aerial socket properly?standby mode (less than 3 W).
Have you chosen the right system? (p. 12).Cleaning the set
Poorly connected euroconnector cables orOnly use a clean,soft and lint-free cloth to clean
aerial sockets are often the cause of picture orthe screen and the casing of your set.Do not use
sound problems (sometimes the connectorsalcohol-based or solvent-based products.
can become half disconnected if the TV set isStill no results?
moved or turned). Check all connections.If your TV set breaks down,never attempt to repair
Peripheral equipment gives a black & white pictureit yourself:contact your dealer's after-sales service.
You have not selected the right socket with the n
19 |