GENERAL INFORMATION / CD PLAYCD PLAY / FEATURES
In-car use (connections supplied or optionally available)Playback information
Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltageY If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded
converter (4.5 V DC, positive pole to the centre pin) and the AY 3501 car adapterproperly, nF dISC is displayed, indicating that the CD has not been
finalized. In that case, use FINALIZE on your CD recorder to complete the
cassette. Any other product may damage the set.
recording.
1 Put the set on a horizontal, vibration-free andY When playing a CD-Rewritable (CD-RW), please note that it takes 3�15
stable surface. Make sure it is in a safe place,12 V DCseconds after pressing 2; for sound reproduction to start.
where the set is neither a danger nor an
Y Playback will stop if you open the CD lid.
obstacle to the driver and the passengers.
Y While the CD is read, 01 --:-- flashes in the display.
2 Plug the voltage converter into the
4,5 V DC
cigarette lighter socket (only for 12 V car 944
OFEFYR
battery, negative grounding), then connectSUMEYHOLDVolume and bass
LINOE
the wired end with 4.5V DC input socket on theVOLOPENUT/
set.Volume adjustment
Y Adjust the volume by using VOL E.
3 If necessary, clean the cigarette lighter socket
to obtain a good electrical contact.
4 Turn down the volume and connect the cassette adapter plug to LINE OUT/p
Bass adjustment
on the set.
YPress DBB to switch the bass enhancement on or
5 Carefully insert the cassette adapter into the car radioOs cassette compartment.off
DBB
yDBB appears if the bass enhancement is
6 Make sure the cord does not hinder your driving.
activated.
7 Decease the volume on the set, if necessary. Start playback on the set and
adjust the sound with the car radio controls.
Y Always remove the voltage converter from the cigarette lighter socket
when the set is not in use.
Note: If your car radio has a LINE IN socket , it is better to use it for the
car radio connection instead of the cassette adapter. Connect the signal
lead to this LINE IN socket and to LINE OUT/p on the set.
Playing a CDSelecting a track and searching
This CD-player can play all kinds of Audio Discs such Selecting a track during playback
as CD-Recordables and CD-Rewritables. Do not try to344Y Briefly press or § once or several times to skip to the current, previous or
9
play a CD-ROM, CDi, VCD, DVD or computer CD.next track.
yPlayback continues with the selected track, and
the trackOs number is displayed.4
1 Push the OPEN 2 slider to open the player.LINEOUT/VOLOPEN4
9
Selecting a track when playback is stopped
2 Insert an audio CD, printed side up, by pressing the
CD onto the hub. 1 Briefly press or § once or several times to select
the desired track. The track number is displayed.
3 Close the player by pressing the lid down.
42 Press 2; to start CD play.
94
4 Press 2; to switch the player on and start playback.yPlayback starts with the selected track.
yThe current track number and elapsed playingE
time are displayed./Searching for a passage during playback
1 Keep or § pressed to find a particular passage in
YYou can pause playback by pressing 2;. a backward or forward direction.
ESP
yThe time at which playback was paused startsySearching starts while playback continues at low
flashing.volume. After 2 seconds the search speeds up.
YYou can continue playback by pressing 2; again.2 Release the button when you reach the desired passage.
yPlayback continues from this position.
5 Press 9 to stop playback.ESP
yThe total number of tracks and the total playingNotes: � If the player is in SCAN mode (see MODE chapter), searching is not
time of the CD are displayed.possible.
� In shuffle, shuffle repeat all or repeat mode (see MODE chapter), or
6 Press 9 again to switch the player off.while playing a program, searching is only possible within the
particular track.
YTo remove the CD, hold it by its edge and press the
hub gently while lifting the CD.
Note: If there is no activity, the set will automatically
switch off after a while to save energy.0 |