Maintenance & safety (See 8)Troubleshooting
CD player and CD handling Safety informationIf a fault occurs, first check the points listed below before taking the set for repair.
Y If the CD player cannot read CDs correctly,Y Place the set on a flat, hard and stable surfaceIf you are unable to remedy a problem by following these hints, consult your dealer or service centre.
use a cleaning CD to clean the lens beforeso that the system does not tilt.
taking the set to repair.
Y Do not expose the set, batteries, CDs toWARNING:Do not open the set as there is a risk of electric shock.Under no
Y The lens of the CD player should never behumidity, rain, sand or excessive heat causedcircumstances should you try to repair the set yourself,as this will
touched!by heating equipment or direct sunlight.invalidate the guarantee.
Y Sudden changes in the surrounding Y The apparatus shall not be exposed to drip-
Problem� Program is active
temperature can cause condensation on theping or splashing.Y Quit program mode
lens of your CD player. Playing a CD is then� Possible cause
not possible. Do not attempt to clean the lensY Adequate ventilation with a minimum gap ofY Remedy--, Er or 01indication
15cm (6 inches) between the ventilation
but leave the set in a warm environment untilholes and surrounding surfaces is necessary to
the moisture evaporates.No sound /power� No CD inserted
prevent heat build-up.Y Insert a CD
YAlways close the CD-tape door to avoid dust� Volume not adjusted
on the lens.Y Do not cover the ventilation openings withY Adjust the VOL� CD badly scratched or dirty
items such as newspapers, table-cloths, cur-Y Replace/ clean CD, see Maintenance
YTo clean the CD, wipe in a straight line fromtains, etc.� Power cord not securely connected
the center towards the edge using a soft,Y Connect the AC power cord properlyNote:A CD badly scratch or dirty may result in
Y No objects filled with liquids, such as vases,improper operation.
lint-free cloth. Do not use cleaning agents as� Batteries dead/ incorrectly inserted
they may damage the disc.shall be placed on the apparatus.� Laser lens steamed up
Y No naked flame sources, such as lighted can-Y Insert (fresh) batteries correctlyYWait until lens has cleared
Y Never write on a CD or attach any stickers� Headphones connected to the set
to it.dles, should be placed on the apparatus.Y Disconnect headphones.� CD-R/CD-RW is blank or not finalized
Y The mechanical parts of the set contain Y Use a finalized CD-R/CD-RW or suitable CD
� CD contains non-audio files
Tape deck maintenanceself-lubricating bearings and must not be oiledAudio disc only
or lubricated.Y Press , § once or more to skip to a CD audio
To ensure quality recording and playback oftrack, instead of the data file.Poor cassette sound quality
the tape deck, clean parts A, B and C asYTo clean the set, use a dry cloth. Do not use
shown, once a month. Use a cotton bud any cleaning agents containing alcohol,Display does not function properly/ No� Dust and dirt on the heads,etc.
slightly moistened with alcohol or a specialammonia, benzene or abrasives as these mayreaction to operation of any of the con-Y Clean deck parts, see Maintenance
head cleaning fluid to clean the deck.harm the housing.trols� Use of incompatible cassette types (METAL or
1 Open the cassette holder by pressingCHROME)
STOPYEJECT.� Electrostatic dischargeY Only use NORMAL (IEC I) for recording
Y Switch off and unplug the set. Reconnect after a
2 Press PLAY and clean the roller C.
few secondsRecording does not work
3 Press PAUSE and clean the heads A, and
the capstan B.The CD skips tracks� Cassette tab(s) may be broken
Y Apply adhesive tape over the missing tab space
4 After cleaning, press STOPYEJECT.� CD damaged or dirty
� Cleaning of the heads can also be done byY Replace or clean CD
playing a cleaning cassette through once.
Environmental information
All unnecessary packaging material has been omitted.The packaging can be easily separated
into three materials: cardboard, polystyrene and plastic.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packaging, dead batteries and old equipment. |
ACEC
