RECORDING
3 With the recorder stopped, press REC TYPE three times to
Manual recording
enter the Manual Record standby mode.
� MANUAL starts to flash and the display shows REC
OPEN / CLOSEPLAPLAY / PY / PAUSEAUSESTOPSTOPTYPERECORDFINALIZEERASEEASY JOGEASY JOGSTORE/STORE/CANCDELEETEnglishOPEN / CLOSEREC
SOURCEMENUMENUMANUAL.
DISPLAY
REM REC TIME TRACKTOTAL REMTRACK TIMESTEP
AUDIO CD RECORDABLE/REWRITAUDIO CD RECORDABLE/REWRITABLEABLERecordable
ENTER
PHONESPHONESINFRA REDINFRA REDSYNCMANUALRECORDPROG
ON / OFFDIGITALICDSHUFFLEALL
4 Play the source first to set the optimal recording level on
Important:the CD recorder.
- Recording from CD-changers should always be started in the
RECORD DISC, RECORD TRACK or MAKE CD mode.5 Rotate the EASY JOG/ENTER key until, on the Record/Play
- Only make analog recordings when digital recording is notLevel bar, all the blue segments are alight, but the red
possible.segments do not light continuously during the loudest
passages.
Preparing for manual recording � Display shows _XX DB. (Decibel, e.g. -3DB)
6 Stop the source.
1 Make sure the disc is absolutely free of scratches and dust
particles.
Start manual recording
2 Press SOURCE repeatedly until (depending on the
1 To start recording, press RECORD on the CD recorder and
connection used):
immediately start the source (from Pause or Stop mode).
� DIGITAL I, OPTICAL I or ANALOG lights up and
� d lights continuously. The track number and recording
DIGITAL 1, OPTICAL or ANALOG appears on the
time appear on the display.
display.
REMTIME TRACKTOTAL REM TRACK TIMESTEP
Y If CHECK INPUT message also flashes, the digital
connection is incorrect.
SYNCMANUALRECORDPROG
DIGITALICDSHUFFLE ALLY To record a 3-second silence at the start of a track, press
ANALOGRWSCAN TRACKPAUSE on the CD recorder before starting the source.OPTICALIREPEAT
Y When Auto Track is ON (default setting), track numbers willY To check the elapsed recording time, press DISPLAY on the
automatically be increased during recording. CD recorder. (This can also be done during the recording.)
Y To switch off the Auto Track function you have to enter2 To stop recording, press STOP on the CD recorder.
� UPDATE lights up and d goes out.
Menu mode.
If you wish to increase track numbers manually, press
Y If STOP was pressed within 3 seconds after RECORD, no
TRACK INCR(ement) on the remote control. For further
recording will take place.
instructions see Menu mode.
Y To interrupt recording, press PAUSE on the CD recorder.
ON (AUTO): The track increments are automatically taken over
d starts to flash. Resume at step 1.
from the digital source material or after 2.7
seconds silence during analog recording.
After recording the display will show UPDATE for several
seconds.
OFF (MANUAL): While recording track numbers can be
incremented manually by pressing TRACKNote: With AUTO TRACK ON, the recorder will stop and go
INCR(ement) on the remote control.to REC STANDBY for 1 minute and then goes to stop
(Minimum track length is 4 sec.) (This canmode automatically. Recordings from DAT, DCC or
also be done in Auto track ON mode.)recordings made analogously will stop after 20 seconds
silence. With AUTO TRACK OFF, the auto stop
Y Track numbers cannot be changed after recording.mode is disabled.
Note: Auto track works only with Consumer Sources with aImportant:
digital output signal according to the IEC 958If you want to play the recorded CDR disc on any
(consumer part) audio standard.regular CD player, it must first be finalized. See
finalizing discs.
Finalized CDRW discs play only on CDRW compatible
CD players.
17 |