Important Note
DKS
Advarsel:Klass 1 laserapparat
Laserrudstr�ling ved �bning n�r sikkerhesafbrydere er ude afVarning!
funktion.Undg� u ts3ttelse for str�ling.Om apparaten anvŠnds p� annat sŠtt Šn i denna bruksanvisning
specificerats,kann anvŠndaren utsŠttas fšr laserstr�lning,som
Bem3rk:šversjruder grŠnsen fšr lŠserklass 1.
Netafbryderen POWER er sekund3rt indkoblet og afbryder ikke
strżmmen fra nette.Den indbyggede netdel er derfor tilsluttet tilObservera!
lysnettet s� l3nge netstikket sidder i stikkontakten.Stršmbrytaren POWER Šr sekundŠrt kopplad och inte bryter
stršmmen fr�an nŠtet Den inbyggda nŠtdelen Šr dŠrfšr ansluten till
elnŠtet s� lŠnge stickproppen sitter i v Šgguttaget.
NSF
Observer:Luokan 1 laserlaite +Klass 1 laserapparat
Nettbryteren POWER er sekundert innkoplet.DenVaroitus!
innebygdenetdelen er derfor ikke frakoplet nettet s� lenge apparatetLaitteen kŠyttŠminen muulla kuin tŠssŠkŠyttšohjeessa mainitulla
er tilsluttet nettkontakten.tavalla saattaa altistaa kÅ yttÅ jÅ n turvallisuusluokan 1 ylittÅ vÅ lle
lasersÅ leilille.
Huom.
Toiminnanvalitsin POWER on kytketty toisiopuolelle,eikÅ se kytke
laitetta irti sŠhkšverkosta.SisŠŠnrakennettu verkko-osa on
kytkettynŠsŠhkšverkkoon aina silloin,kun pistoke on pistorasiassa.
Important Note for Users in the UK
Mains plugHow to connect a plug
This apparatus is fitted with an approved 13 Amp plug.ToThe wires in the mains lead are coloured with the following
change a fuse in this type of plug proceed as follows:code: blue = neutral (N), brown = live (L).
1 Remove fuse cover and fuse.As these colours may not correspond with the colour
2 Fix new fuse which should be a BS1362 5 Amp,markings identifying the terminals in your plug, proceed as
A.S.T.A. or BSI approved type.follows:
3 Refit the fuse cover.Y Connect the blue wire to the terminal marked N or
coloured black.
If the fitted plug is not suitable for your socket outlets, it shouldY Connect the brown wire to the terminal marked L
be cut off and an appropriate plug fitted in its place.or coloured red.
If the mains plug contains a fuse, this should have a value of 5Y Do not connect either wire to the earth terminal in
Amp. If a plug without a fuse is used, the fuse at thethe plug, marked E (or e) or coloured green
distribution board should not be greater than 5 Amp.(or green and yellow).
Before replacing the plug cover, make certain that the cord grip
Note:The severed plug must be disposed of to avoid a possible
is clamped over the sheath of the lead - not simply over the
shock hazard should it be inserted into a 13 Amp sockettwo wires.
elsewhere.
Copyright in the U.K.
Recording and playback of material may require
consent.See Copyright Act 1956 and The PerformerOs
Protection Acts 1958 to 1972.
3139 246 11931 |
ACEC
