� Progressive Scan (Y Pr/Cr Pb/Cb connection only)
Disc AudioDOLBYDIGITAL/PCM
Progressive Scan Video provides the highest quality picturesDisc SubtitleStream/PCM
with less flickering.Disc MenuPCM
Rating
If you are using the Component Video jacks, but are
Country CodeSample Freq.
connecting the DVD Player to a standard (analog)TV Aspect48 KHz
television, set Progressive Scan to Off.Menu Language96KHz
Progressive Scan
If you are using the Component Video jacks for connection
Digital Audio Output
to a TV or monitor that is compatible with a progressive5.1 Speaker Setup
scan signal, set Progressive Scan to On.Others
Notes:
�Sample Frequency
� Progressive Scan only works when the VIDEO OUTPUT
To change the Sample Frequency setting, first select the
switch on the rear panel is set to COMPONENT/
desired Digital Audio Output as indicated above.
PROGRESSIVE SCAN.
If your receiver or amplifier is NOT capable of handling
� Progressive Scan only appears in the menu if the VIDEO
96KHz signals, select 48KHz. When this choice is made, this
OUTPUT switch is set to COMPONENT/PROGRESSIVE SCAN.
� Make sure the TVOs Sync Mode setting is correct. Forunit will automatically convert any 96KHz signals to 48KHz
so your system can decode them.
example, on some Philips TVs, set OSYNC MODE� to OSYNC
If your receiver or amplifier is capable of handling 96KHz
MODE 2.� An incorrect Sync Mode setting will cause the
picture to shift off-center on the TV screen while usingsignals, select 96KHz. When this choice is made, this unit will
Progressive Scan. Check your TV ownerOs manual for details onpass each type of signal through without any further
correct Sync Mode settings.processing.
Caution:
� Once the setting for progressive scan output is entered, anLanguage
image will only be visible on a progressive scan compatible TV or�Language (Disc Audio, Disc Subtitle and Disc
monitor. If you set Progressive Scan to On in error, you must resetMenu)
the unit. Press STOP to stop any disc that is playing. Next, press
STOP again and hold it for five seconds before releasing it. TheSelect a language for the discOs Menu, Audio and Subtitle.
Audio language and Subtitle language also can be adapted
video output will be restored to the standard setting, and a
using the On-Screen Display. Press the 3/4 buttons to
picture will once again be visible on a conventional analog TV or
monitor.select an item, then press the 1/2 buttons to choose a
setting in the On-Screen Display (menu bar).
Disc AudioOffThe change will be effective only if the language is available
Disc SubtitleOnon the Disc (as shown on Disc case).
Disc Menu
Rating
Country CodeDisc AudioOriginal
TV AspectDisc SubtitleEnglish
Menu LanguageDisc MenuFrench
Progressive ScanRatingGerman
Digital Audio OutputCountry CodeSpanish
5.1 Speaker SetupTV AspectItalian
OthersMenu LanguageChinese
Progressive ScanPolish
Digital Audio OutputHungarian
5.1 Speaker SetupRussian
Sound
OthersOther ? ? ? ?
�Digital Audio Output
Each DVD disc has a variety of audio output options. Set�Menu Language
the playerOs Digital Audio Output according to the type ofSelect the language for the DVD PlayerOs Menu. This is the
audio system you use.menu you see when you press the SYSTEM MENU button.
DOLBY DIGITAL/PCM: Select ODOLBY DIGITAL/ PCM� if
you connected the DVD PlayerOs DIGITAL OUTDisc AudioEnglish
(COAXIAL or OPTICAL) jack to a Dolby Digital decoderDisc SubtitleSpanish
Disc MenuFrench
(or an amplifier or other equipment with a Dolby Digital
Rating
decoder).Country Code
TV Aspect
Stream/PCM: Select OStream/PCM� if you connected the
Menu Language
DVD PlayerOs DIGITAL OUT (COAXIAL or OPTICAL) jackProgressive Scan
to an amplifier or other equipment with a DTS decoder,Digital Audio Output
Dolby Digital decoder or MPEG decoder.5.1 Speaker Setup
Others
PCM: Select OPCM� if you connected the DVD PlayerOs
DIGITAL OUT (COAXIAL or OPTICAL) jack to an
amplifier or other equipment with linear PCM only (or Mini
Disc (MD) recorder or Digital Audio Tape (DAT) deck).
14PREPARATION |
ACEC
