H9924RD_EN_0316 3/17/05 10:11 AM Page 11
VCR Manual Recording
4 Select ORECORD SET UP� with K/L and confirm with B.
Direct dubbing
5 Select ORECORD LINK� with K/L.
Follow the steps below to copy a DVD or video disc to a
6 Select function OON� with B.
video tape.This will be possible only if the DVD is not copy7 To end, press STATUS/EXIT.English
protected.
Switching off Record Link1 Put a video tape in the cassette compartment. Make sure the
To switch off the function, select OOFF� with B.
video tapeOs record tab is intact and the video tape is long
enough to record the disc.8 Insert a video tape.SELECT KL CHOOSE B
2 Press VCR.
9 Programme the satellite receiver
RECORD SPEED [SP]
3 Select the recording speed.with the required informationDIRECT RECORD [OFF]
?RECORD LINK[OFF]Details are at Selecting the recording speed (SP or LP).(programme number of the TV
4 Put the DVD you want to copy in the disc tray.channel, start time, end time).
5 Press DVD.
If necessary, please see the
6 Press PLAY B.While disc is playing, press PAUSE F at theoperating instructions for your
END=EXITpoint you wish to start recording.
satellite receiver.
7 Press D. DUBBING to record.10 Press TIMER SET.The DVD/ VCR is now ready to record.The
beginning and end of the recording is controlled via scart
To pause the recording: Press VCR, then PAUSE F.
socket AV2 (DECODER).
To resume recording: Press PAUSE F again.
To stop the recording: Press VCR, then STOP C.
Direct Record
With Direct Record, you can record the right TV channel in
seconds even if your DVD/ VCR is switched off. If the recordingCopying a video tape
is started manually, the DVD/ VCR uses the current TV channelYou can make copies of video tapes made by friends or
set on the TV. You will find more information on how torelatives for your own enjoyment.
switch Direct Record on or off in the next section. Make sure
WARNING:
that your DVD/ VCR socket (AV1/TV) and the TV are
Unauthorized recordings of copyrighted video tapes
connected by a SCART cable.
may be an infringement of copyright laws.
1 On the TV, select the programme number you want to make
the recording from.Connect the recording DVD/ VCR (this unit) and the playback
2 Press RECORD I with the DVD/ VCR switched off.video recorder (another video recorder) by using scart socket
3 Stop recording with STOP C.AV2 (DECODER) or front AUDIO/ VIDEO IN jacks.
1 Insert a pre-recorded video tape into the playback DVD/ VCR.
How does Direct Record work?2 Insert a blank video tape, or one you want to record over, into
The DVD/ VCR compares the TV channel selected on the TV withthe cassette compartment of this unit.
its stored TV channels via the SCART cable. If the same TV
3 Select programme number AV2 or AV3 on this unit.
channel is found, it switches the DVD/ VCR to the corresponding
programme number and starts recording. Please do not changeProgramme numbers of AV2 scart socket and front
the TV channel on the TV during the search so as not to affectAUDIO/ VIDEO IN jacks
the process.If you are using the scart socket AV2 (DECODER),
select programme number AV2 with 0.0.2.
If you are using the front AUDIO/ VIDEO IN jacks,
Switching Direct Record on or offselect programme number AV3 with 0.0.3.
1 Switch on the TV. If required, select the programme number for4 Press RECORD I on the front panel of this unit.
the DVD/ VCR.5 Begin playback of the video tape in the playback DVD/ VCR.
2 Press DISC/VCR MENU.The main menu will appear.6 To stop recording, press STOP C on this unit, then stop
3 Select ORECORD SET UP� with K/L and confirm with B.playback of the video tape in the playing DVD/ VCR.
4 Select ODIRECT RECORD�, withSELECT KL CHOOSE B
Y For the best results during dubbing, use the DVD/ VCROs front
K/L. Select OOFF� (Direct Record
RECORD SPEED [SP]panel controls whenever possible.The remote control might
off) or OON� (Direct Record on)?DIRECT RECORD [OFF]
affect the playback DVD/ VCROs operation.
with B.RECORD LINK[OFF]
Y If video or colour fades in and out, you may be copying a copy
5 To end, press STATUS/EXIT.guarded video tape.
6 Press STANDBY-ONyy.
END=EXIT
Programming a Recording (TIMER)
General information
What is OVPS/PDC�?
Use a TIMER programming to automatically start and stop aOVPS� (Video Programming System)/ OPDC� (Programme Delivery
recording at a later time or date.The DVD/ VCR will switch toControl) are used to control the start and duration of TV channel
the right programme number and begin recording at therecordings. If a TV programme starts earlier or ends later than
scheduled, the DVD/ VCR will turn on and off at the correct time.
correct time.With this unit, you can pre-programme up to 8
What do I need to know about OVPS/PDC�?
recordings within a period of one year.To make a programmed
Usually the VPS or PDC time is the same as the start time. But if
recording, your DVD/ VCR needs to know:
your TV guide shows a VPS or PDC time which is different from
* the date you want to make the recordingthe programmeOs scheduled start time, e.g. 20.10 (VPS/PDC
* the programme number of the TV channel20.14), you must enter the VPS/PDC time exact to the minute. If
* the start and stop time of the recordingyou want a start time different from the VPS/PDC time, you must
* VPS or PDC on or offswitch VPS/PDC off.
This information is saved in a TIMER block.
11 |
ACEC
