Settings are canceled.
Troubleshooting
When the power is turned off by power failure or by
Incorrect operations are often mistaken for trouble andunplugging the power cord, settings will be canceled.
malfunctions. If you think that there is something wrong\ Before unplugging the power cord, press
with this component, check the points below. STANDBY/ON and check that O--OFF--�
Sometimes the trouble may lie in another component.disappears in the display.
Inspect the other components and electrical appliances
being used. If the trouble cannot be rectified even afterNo picture.
exercising the checks listed below, ask your nearestConnection is incorrect.
PIONEER authorized service center or your dealer to\ Check that cord connections are correct and that
carry out repair work.plugs are firmly connected.
Operation (settings) of TV or AV amplifier is not
appropriate.
The disc table comes back out automatically, shortly
\ Be sure that your TV, receiver, or amplifier is set
after the disc table is closed.
up to view DVD playback.
The disc is dirty or warped.
\ Refer to �Disc CareO (page 56).The screen is stretched or aspect does not change.
The disc is not placed properly on the disc table.The multi aspect setting is not appropriate.
\ Use the disc table guide to align the disc (page 20).\ Change the aspect setting in the [TV Screen]
setting in the Setup screen Video 1 menu to the
Region number does not conform with this unit.screen type most appropriate to the TV or monitor
\ If the region number on the disc does not matchyou are using (page 29).
the number on the player, the disc cannot be used
(page 62).Picture disturbance during playback or dark.
This is not a malfunction.
There is condensation on the operating section of the
player.\ This player is compatible with Macro-Vision
System copy guard. Some discs include a copy
\ Allow time for condensation to evaporate. If player
is near an air conditioning unit, you should moveprevention signal, and when this type of disc is
played back, stripes etc., may appear on some
the player (page 57).
sections of the picture depending on the TV.
Playback is not possible.The TV system may be set inapproriately.
The disc has been loaded upside down.\ See �Setting the TV SystemO on page 17.
\ Check that the disc has been loaded with the label
side facing up.Discs respond differently to particular player
functions which may result in the screen becoming
\ A Super VCD that does not conform with the IECblack for a brief instant or shaking slightly when the
standards might not play normally.function is executed.
\ These problems are largely due to differences
mark appears on screen.
between discs and disc content and are not
The selected function does not operate for that disc.
malfunctions of this player.
mark appears on screen.
Audio is output from the analog output jacks but not
The operation is prohibited by the player.
from the digital output jack.
Player settings are incorrect.
Picture playback stops and the operation buttons
\ In the Audio 1 menu, check that the appropriate
cannot be used.
digital audio output formats are selected, and that
\ Stop disc playback (press STOP 7), then start
the [Digital Out] setting is not set to [Off] (page
playback again.
27).
New settings made in the Setup screen menus whileWhen recorded on a VCR or passed through an AVADDITIONAL INFORMA
a disc is playing are ineffective.
selector, there is disturbance in the playback picture.
Some settings can be changed while a disc is playing,
This is not a malfunction.
but are not effective. This is not a malfunction.
\ Due to the playerOs copy protection circuits,
\ Make the same setting when the player is
connection of this device through a VCR or an AV
stopped.
selector may prevent recording or cause picture
\ Stop disc playback (press STOP 7), then startproblems.
playback again. When playback is resumed, the
new settings should be in effect. Please note thatRemote control operation is not possible.
TION
making settings in the Setup screen menus mayThe rear panel control input jack on the player is being
cancel the resume function.used.
\ Point the remote control at the component that
When making changes in the Setup screen menus,the player is connected to (page 16).
is displayed.
The remote control is too far from the player, or the
There is a Video CD, CD or MP3 loaded in the player
angle with the remote sensor is too wide.
and the setting that was changed only applies to DVD
\ Be sure to operate the remote from a location
performance.
within its operating range (page 8).
\ The setting will be effective the next time a DVD
is loaded.The batteries are exhausted.
\ Replace the exhausted batteries with all new
batteries (page 8).
59
En |
ACEC
