V-Accordion r
Important notes
2. Important notes
In addition to the items listed under Using the unit safely on p. 7, please read and observe the following:
Power supply" Do not paste stickers, decals or the like on this instrument. Peeling
these off, particularly when strong adhesives have been used, can
" Do not connect the FR-3 to same electrical outlet that is being
used by an electrical appliance that is controlled by an inverter damage the instruments exterior finish (the stickers provided with
this instrument feature a weak adhesive).
(such as a refrigerator, washing machine, microwave oven, or air
conditioner), or that contains a motor. Depending on the way in
which the electrical appliance is used, power supply noise may Maintenance
cause this unit to malfunction or may produce audible noise. If it is " For everyday cleaning wipe the FR-3 with a soft, dry cloth or one
not practical to use a separate electrical outlet, connect a power that has been slightly dampened with water. To remove stubborn
supply noise filter between this unit and the electrical outlet.dirt, use a mild, non-abrasive detergent. Afterwards, be sure to
" Do not use this instrument on the same power circuit with any wipe the instrument thoroughly with a soft, dry cloth.
device that will generate line noise (such as an electric motor or " Never use benzene, thinner, alcohol or solvents of any kind, to
variable lighting system).avoid the possibility of discoloration and/or deformation.
" Before connecting the FR-3 to other devices, turn off the power to
all units. This will help prevent malfunctions and/or damage to Repairs and data
speakers or other devices." Please be aware that all data contained in the instruments mem-
" The AC adaptor will begin to generate heat after long hours of ory may be lost when it is sent for repairs. In certain cases (such as
when circuitry related to memory itself is out of order), we regret
consecutive use. This is normal, and is not a cause for concern.
" Although the display and LEDs are dark when the POWER switch is that it may not be possible to restore the data. Roland assumes no
liability concerning such loss of data.
off, this does not mean that the unit has been completely discon-
nected from the power source. To turn off the power completely,
first turn off the POWER switch, then unplug the power cord from Additional precautions
the wall outlet. For this reason, the outlet to which you connect " When moved from one location to another where the temperature
the power cords plug should be one that is within easy reach.and/or humidity is very different, water droplets (condensation)
may form inside the FR-3. Damage or malfunction may result if
Placementyou attempt to use the FR-3 in this condition. Therefore, before
using the FR-3, you must allow it to stand for several hours, until
" Using the FR-3 near power amplifiers (or other equipment con-the condensation has completely evaporated.
taining large power transformers) may induce hum. To alleviate
the problem, change the orientation of this unit; or move it farther " Please be aware that the memory contents can be irretrievably lost
away from the source of interference.as a result of a malfunction or the improper operation of the
instrument. Therefore, be sure to archive important settings using
" This device may interfere with radio and television reception. Do the FR-3s Bulk Dump function (see p. 52).
not use this device in the vicinity of such receivers.
" Use a reasonable amount of care when using the instruments
" Do not place the FR-3 near devices that produce a strong mag-buttons, other controls and jacks/connectors. Rough handling can
netic field (e.g., loudspeakers).
lead to malfunctions.
" Install the FR-3 on a solid, level surface." Never strike or apply strong pressure to the display.
" Noise may be produced if wireless communications devices, such
" When connecting/disconnecting cables, grasp the connector
as cell phones, are operated in the vicinity of this unit. Such noise itselfnever pull on the cable. This way you will avoid causing
could occur when receiving or initiating a call or while conversing.
Should you experience such problems, relocate such wireless shorts or damage to the cables internal elements.
devices so they are at a greater distance from this unit or switch " A small amount of heat will radiate from the instrument during
them off.normal operation. This is perfectly normal.
" Do not expose the unit to direct sunlight, place it near devices that " To avoid disturbing your neighbors, try to keep the instruments
radiate heat, leave it inside an enclosed vehicle or otherwise sub-volume at reasonable levels. You may prefer to use headphones, so
you do not need to be concerned about those around you (espe-
ject it to temperature extremes. Also, do not allow lighting devices
that normally are used while their light source is very close to the cially late at night).
unit (such as a piano light) or powerful spotlights to shine upon " When you need to transport the instrument, package it in the box
the same area of the unit for extended periods of time. Excessive (including padding) that it came in. Otherwise, you will need to use
heat can deform or discolor the unit.equivalent packaging materials or a flightcase.
" To avoid possible breakdown, do not use the unit in a wet area, " Use Roland cables to make audio connections. If using some other
such as an area exposed to rain or other moisture.make of connection cable, please note the following precautions.
" Do not allow rubber, vinyl or similar materials to remain on the Some connection cables contain resistors. Do not use cables that
instrument for long periods of time. Such objects can discolor or incorporate resistors for connecting to this unit. The use of such
otherwise harmfully affect the finish.cables can cause the sound level to be extremely low or impossible
" Do not put anything that contains water (e.g., flower vases) on the to hear. For information on cable specifications, contact the man-
ufacturer of the cable.
instrument. Also, avoid the use of insecticides, perfumes, alcohol,
nail polish, spray cans, etc., near the unit. Swiftly wipe away any
liquid that spills on the unit using a dry, soft cloth.
" Do not allow objects to remain on top of the keyboard or buttons.
This can be the cause of malfunction, such as keys or buttons ceas-
ing to produce sound.
9 |
ACEC
