Filter Reset NOTE: Your ice maker has an automatic shutoff. The ice maker
See ?Water Filtration System.?sensors will automatically stop ice production, but the control will
remain in the ON position.
Removing and Replacing Ice Storage Bin
To Remove the Ice Storage Bin:
1. Hold the base of the storage bin and press the release button
on the lower right.
User Preferences2. Pull the storage bin out until resistance is felt. Lift up the front
of the ice bin and remove.
The control center allows you to set user preferences, if desired. 3. Press the switch to the OFF position
Temperature Display (F_C)To Replace the Ice Storage Bin:
This preference allows you to change the temperature display.IMPORTANT: It may be necessary to turn the auger driver,
F - Temperature in degrees Fahrenheitbehind the ice bin, counterclockwise to properly align the ice bin
C - Temperature in degrees Celsius with the auger driver. The ice storage bin must be locked in place
for proper ice dispensing.
Alarm (AL)
1. Press the switch to the ON position
This preference allows you to turn off the sound of all alarms.2. Slide the ice bin into the guide rails located on either side of
ON - You will hear the alarm sound.
the enclosure.
OFF - You will not hear the alarm sound.3. Push the ice bin in until resistance is felt. Raise the front
Auto Light Level Selection (LL)slightly and push the ice bin in until an audible ?click? is
This preference allows you to adjust the dispenser light level from heard.
dimmest to brightest (settings 1 through 9).
NOTE: The Auto Light feature on the control center must be
selected to activate this preference.
Sabbath Mode (SAB)
ON - All control center lights, interior lights and alarm tones will
be disabled.
OFF - All control center lights, interior lights and alarm tones will
be enabled.
NOTE: Press the door alarm touch pad for three seconds to
restore all lights.
To Access the User Preferences Menu:
1. Press and hold the Door Alarm touch pad for three seconds.
The preference name will appear in the Freezer display and A
the preference status (F or C) or (ON or OFF) will appear in the A.Auger driver
Refrigerator display.
2. Use the Freezer (+) or (-) touch pads to scroll through the
preference names. When the desired preference name is Ice Production Rate
displayed, press the Refrigerator (+) or (-) touch pads to
change the preference status. Allow 24 hours to produce the first batch of ice. Discard the
3. Set your preferences by pressing and holding the Door Alarm first three batches of ice produced.
touch pad for three seconds. Â The ice maker should produce approximately 8 to 12 batches
of ice in a 24-hour period.
Crisper Humidity Control  To increase ice production, lower the freezer and refrigerator
temperature. See ?Using the Controls.? Wait 24 hours
(on some models)
You can control the amount of humidity in the moisture-sealed between adjustments.
crisper. Adjust the control to any setting between LOW and
HIGH.Remember
LOW (open) for best storage of fruits and vegetables with skins. Â The quality of your ice will be only as good as the quality of
HIGH (closed) for best storage of fresh, leafy vegetables.
the water supplied to your ice maker. Avoid connecting the
ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice maker
Ice Maker and Ice Storage Binand lead to poor quality ice. If a softened water supply cannot
The ice maker and storage bin are located in the upper left-hand
side of the refrigerator compartment. be avoided, make sure the water softener is operating
properly and is well maintained.
Turning the Ice Maker On/Off Do not use anything sharp to break up the ice in the bin. This
can cause damage to the ice bin and dispenser mechanism.
The On/Off switch is located on the front of the ice maker. Do not store anything on top of the ice maker or in the ice
storage bin.
To turn on the ice maker, press the switch to the ON position.
To manually turn off the ice maker, press the switch to the OFF
position.
10 |
ACEC
