AFTER SALES SERVICEservice number (i.e., the number that follows the word Declaration of conformityThis hob has been designed, constructed and marketed
Before you call the After Sales ServiceSERVICE on the rating plate under the hob itself). The in compliance with:
Make sure that you cannot solve the problem yourself service number is also indicated on the guarantee This hob is suitable for contact with foodstuffs, and - safety requirements of EEC Directive ?Low voltage?
complies with EEC Directive 89/109.
following the points described in chapter booklet;73/23;
?Troubleshooting Guide?.your full address;This hob (Class Y) has been designed to be used only - protection requirements of EEC Directive
for cooking. Any other use (such as heating a room) is
If after the above checks the fault still occurs, get in your telephone number.?EMC? 89/336;
If any repairs are required, please contact an authorised improper and dangerous.- requirements of EEC Directive 93/68.
touch with the nearest After Sales Service.
After Sales Service (to guarantee that original spare parts
Please give:will be used and repairs carried out correctly).The Manufacturer reserves the right to change product
a short description of the fault;specifications without prior notice.
Failure to comply with these instructions may
the exact type and model of hob;compromise the safety and quality of the product.
INSTALLATION
RecommendationsIf the worktop is made of wood, use the spring clips
and screws provided.
Important: Disconnect the hob from the mains before
1.Secure the spring clips (A) (fig.1) with the screws
carrying out any installation work or servicing.
All electrical connections must be made before provided (B) (fig. 1) as shown, paying attention to the
specified distances.
connecting the appliance to the power supply.
2.Fit the hob into the worktop.
Installation must be carried out by a qualified technician
in accordance with the manufacturer's instructions and If the worktop is made of marble, plastic, ceramic,
stone, etc., the hob must be secured with special
in compliance with local regulations.
Unpack the hob and make sure that the appliance has brackets (C) (fig. 2).
not been damaged during transport. If you are not 1.Fit the hob into the worktop (fig.1).
sure contact the dealer or the nearest service 2.Place the 4 brackets (C) in position in accordance with the
centre.thickness of the worktop as shown in fig. 2.
3.Fasten the 4 screws (D) in the positions (E) (fig.2).Fig. 1
Preparing the housing unit
Electrical connection
Cut the worktop to fit before installing the appliance.
Carefully remove any shavings or sawdust that could Regulations require that the appliance be earthed.
prevent the appliance from running properly.Connection to the mains must be carried out by a
Attention: to install the hob on other surfaces than wood qualified technician in accordance with the
(marble, plastic, ceramic, marble, stone, etc.) remember to manufacturer's instructions and in compliance with local
ask After Sales Service for the fixing plates (fig. 2) Code 4819 regulations.
404 78697.The installer is responsible for connecting appliances
The hob must be fitted in a worktop with a minimum correctly to the mains and for observing the safety
thickness of 20 mm and a maximum of 50 mm.regulations.
Insert a separator panel at a minimum distance of The oven power cable must be long enough to connect
90 mm from the bottom of the hob, so that it cannot be the built-in appliance to the mains.
accessed by the user.Observance of safety directives requires that a multi-
If there is an oven under the hob, make sure that it is pole switch with a minimum contact gap of 3 mm be
manufactured by us and equipped with a cooling used for the installation.
system.Do not use multiple plug adapters or extension leads.
There must be nothing between the hob and the oven After the oven has been installed, the electrical
(e.g. cables, insulating material, etc.).components must be inaccessible.Fig. 2Fig. 3
An adjacent column unit must be installed at least
Connecting the oven to the power supply
100 mm from the edge of the hob.
Cut an opening in the worktop of the given dimensions.Note: the yellow/green earth wire must be connected to the
We recommend you seal the internal edges of the screw with the symbol .
worktop with wood glue or silicone. Strip approx. 70 mm of the cable sheath from the
If not already in place, apply the supplied seal to the power supply cable (G).
hob, after cleaning the adhesive surface thoroughly.Strip approx. 10 mm of sheath from the conductors.
Insert the cable (G) through the opening in the lid (F).
Glass-ceramic hobInsert the cable into the cable clamp and connect the
Important: remove any protective film before installing conductors to the terminal block as indicated in the
the hob.diagram printed on the lid.
Make sure that that the opening in the worktop for the hob is Secure the power cable (G) by means of the cable
cut according to the dimensions given in the drawing, paying clamp.
attention to the tolerance range.Refit the protection lid (F).
The hob should not be forced into the worktop. Forcing the After the electrical connection, fit the hob from the top
glass-ceramic top may cause it to crack (even at a later date)!and hook it to the fixing springs, according to the
illustration. |
ACEC
