3gb10168.fm Page 66 Tuesday, June 1, 2004 3:47 PM
a. Water inlet fault (no or insufficient water c. Electrical module fault
supply)For models with a fault display ?F4? to ?F15? are
For models with a fault display, the ?Water tap? displayed and some or all Spin Speed Selection
indicator is on or the display alternately shows ?FH?. LEDs are flashing. Switch off the appliance. Select a
Switch off the appliance by turning the programme programme and press the ?Start/Pause? button
selector to the ?? position and unplug it.once again. The programme will continue.
For models with no fault display, the washing For models without a fault display the washing
machine stops in the appropriate step. Switch off machine stops in the appropriate step. Switch the
the appliance and unplug it.appliance first off, then on. The programme will
Check whether:continue.
? the water tap is completely open, and the water If the fault re-occurs, contact After Sales Service
supply pressure is sufficient;(See ?After-Sales Service?).
? the water inlet hose is kinked;d.Water Stop fault (if available)
? the mesh filters are blocked (see ?Care and The ?Water Stop? may have been triggered by:
Maintenance? / ?Water Hose Mesh Filters?);
? the water inlet hose is frozen.1.too much foam.
2.a leak in the inlet hose or in the appliance.
Reconnect the appliance to the electrical supply.
In this case the pump is switched on automatically
For models with a fault display, reselect the desired in order to pump the water out.
programme and press the ?Start/Pause? button
again to continue with the programme (do not add For models with a fault display the light of the
detergent for this programme).?Water Stop? indication is on. The display shows
For models without a fault display continue the ?FA? or alternately ?F? and ?A? and the pump is
running. Switch off the appliance by turning the
programme by pressing the ?On/Off? button
again (do not add detergent for this programme).programme selector to the ?? position, unplug
If the fault re-occurs, contact After-Sales Service the appliance and make sure that the water tap is
closed.
(see ?After-Sales Service?).
b.Draining out faultFor models without a fault display the washing
machine stops in the appropriate step. Switch off
For models with a fault display, depending on the
model, the display shows statically or alternately the appliance, , unplug the appliance and make sure
?FP?. Switch off the appliance by turning the that the water tap is closed.
programme selector to the ?? position and Tilt the appliance forwards carefully to allow the
unplug it.collected water to flow out.
For models with no fault display, the washing Then:
machine stops in the appropriate step. Switch off 1.plug in the appliance,
the appliance and unplug it.
2.turn the water tap on (if water immediately flows
Check whether:
? the drain hose is kinked (see ?Installation into the appliance again, without the appliance
being started, close water supply and call After-
Guide?);Sales Service).
? the pump / filter are blocked (see ?Removing the
For models with a fault display reselect the desired
Filter / Draining Residual Water?);programme and press the ?Start/Pause? button
IMPORTANT: before draining, allow the wash
water to cool down.again to continue with the programme (do not add
detergent for this programme).
? the drain hose is frozen.
Connect the appliance to the electrical supply.For models without a fault display continue the
programme by pressing the ?On/Off? button
For models with a fault display reselect the desired
programme and press the ?Start/Pause? button again (do not add detergent for this programme).
If the fault re-occurs, contact After-Sales Service
again to continue with the programme (do not add
detergent for this programme).(see ?After-Sales Service?).
For models without a fault display continue the
programme by pressing the ?On/Off? button
again (do not add detergent for this programme).
If the fault re-occurs, contact After-Sales Service
(see ?After-Sales Service?).
66 |
ACEC
