3GB15026.fm Page 2 Monday, June 24, 2002 5:20 PM
Note: The programme stops to ?Rinse Hold? at the The indicator lamps show the sequence reached in
CONSUMPTION DATA
time the ?Rinse Hold? light in the programme flow the programme. After starting the programme, the
indication is on.sequence indication runs from left to right through
Temperature SelectorLoadWaterEnergyApprox. Programme
ProgrammeDurationTerminate the ?Rinse Hold? option:Wash, Rinse, Spin.
(°C)(kg)(l)(kWh)(hours : minutes)*? Press the ?Rinse Hold? button again; the When the sequence of the programme is finished
Cotton905.044**1.601:55programme will terminate automatically with the the corresponding lamp goes out.
final spin cycle for the present wash programme.
Cotton605.0390.952:00DOOR LOCK
Cotton405.0390.552:00? If you do not wish to spin the clothes, turn the
programme selector knob to the ?Drain? During the first 15 minutes of the cotton and
Synthetics602.5550.701:30
programme and press the ?Start/Pause? button synthetics programmes the door can be opened for
Synthetics402.5500.501:15again when flashing.adding further laundry.
Daily403.0450.501:00?Variable Spin? buttonThe door can be opened when the ?Door Open?
Rapid Plus303.0350.400:30? Every programme has an automatic predefined indication is shining.
Delicates301.5500.500:45maximum spin speed.
PROGRAMME END
Wool401.0500.500:40? Press the button to set another spin speed.
Handwash301.0350.400:35? If the spin speed ?0? is selected, the final ? The remaining time is on ?0:00? and all the
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized spinning is cancelled but intermediate spin lights of the programme sequence indication
conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in peaks remain during rinse. The water is drained are off.
the table in relation to the water supply pressure and temperature, the load and the type of wash.out only.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the 1. Turn the programme selector to the ??
household conditions applicable at that time.position.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.START DELAY
2. Turn the water supply tap off.
?Eco? buttonThe ?Start Delay? allows to run the machine at the 3. Open the door and unload the machine.
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE
? The duration of the wash is extended and the PROGRAMMEconsumer?s convenience, for example at night 4. Close the tap and leave the door ajar to allow
temperature reduced to save up to 40% of energy when electricity is cheaper.the drum to dry out.
Add the detergents as described in the programme but maintaining good washing results.
? Select programme, temperature and options.
table or in the chapter ?Detergents and Additives? in ?Easy Ironing? buttonCHANGE THE PROGRAMME, TEMPERATURE,
the booklet.? Press the ?Start Delay? button to select the OPTIONS AFTER PROGRAMME START
? Can be used together with Cotton, Synthetics and delay time by 1 to 19 hours;
1. Turn the programme selector knob to the Daily programmes to make ironing easier.
desired programme.? Increases the water quantity and the clothes are ?Press the ?Start/ Pause? button. The ?Start 1. Press the ?Start/Pause? button to pause the
2. The remaining time display shows the duration of Delay? light flashes until the programme starts.programme. The light flashes.
spun very soft.
the chosen programme (in hours and minutes) ?Prewash? button? The time delay indication disappears when the 2. Select the new programme (with temperature),
and the pilot lamp of the ?Start/Pause? button programme starts and it is replaced by the any options and another spin speed if you
? Only for heavily soiled loads (for example sand,
is flashing.granular dirt) sensible. The cycle time increases remaining time.want.
3. The programme sequence and the predefined ? The number of hours preselected can later be 3. Press the ?Start/Pause? button again. The
spin speed indication corresponding to the approximately 15 min.reduced pressing again the ?Start Delay? new programme continues at the same position
?Intensive Rinse? button
selected programme lights up.button.where the previous programme was
The recommended temperature (see the indicator) ? A further rinse cycle is added.interrupted. Do not add detergent for this
? This option is particularly suitable for areas with To cancel the ?Start Delay?.
can be altered by pressing ?+? or ?-? button.very soft water, washing baby linen and helps ? Turn the programme selector to the ? ? programme.
SELECT ANY DESIRED OPTIONpeople with allergies.position.CANCEL A PROGRAMME BEFORE THE END
Selecting any option the indication lights up.?Rinse Hold? button? Reselect the desired programme and options
? The laundry remains in the last rinse water without and press the ?Start/Pause? button.1. Press the ?Start/Pause? button to pause the
When the combination of programme, additional progressing to the final spin cycle to avoid creasing programme. The light flashes.
options and temperature is not possible, the PROGRAMME START
indication lights switch off automatically. and prevent colours from changing.2. Set the programme selector to ?Drain?. The
? This option is particularly recommended for the spin indicators show ?0? and the remaining
Unsuitable combinations of options are Open the tap and press the ?Start/Pause? button.
deselected automatically.programme ?Synthetics?, ?Daily? and ?Delicates?.The pilot lamp of the ?Start/Pause? button lights up.time shows ?0:02?.
? This function is particularly useful if you want to 3. Press the ?Start/Pause? button to start the
postpone spinning to a later time, or if you want
drain programme.
to drain only.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 15026
Black process 45.0° 100.0 LPI |
ACEC
