3GB20104.fm Page 4 Wednesday, July 7, 2004 2:18 PM
Please read the Instructions Manual carefully before using your new washing machine
GB
Quick Reference Guide
Programme selectorStart Delay
To select a programme, turn the knob. Delays the start of the wash cycle by 1 to 16 hours. Each time the
The corresponding symbol will appear on the display. button is pressed, the start of the wash cycle is delayed by 1 hour.
To change the programme once the wash cycle has Prewash
started, turn the knob to ? ? and set the new Only for heavily soiled laundry (e.g. sand, granular dirt). Programmes
programme. with Prewash last approx. 15 minutes longer.
When the knob is on ? ? three dashes blink on the
Intensive rinse button
display.
More water and a longer time in rinse cycle is added.
Start buttonThe intensive rinse function is especially suitable for areas with
When you press this button, it lights up and the wash
particularly soft water, for baby clothes and to help people with
cycle starts. At the end of the wash cycle the light will
allergies.
turn off and END will appear on the display.
Rinse Hold
The laundry remains in the last rinse water without progressing to the
On/Off buttonfinal spin cycle to avoid creasing and prevent colours from changing.
This button switches the washing machine on/off.
This option is particularly recommended for the programme
?Synthetics? or ?Delicate?.
This function is particularly useful if you want to postpone spinning
to a later time or when you do not wish to spin the clothes.
Changing or interrupting the programme during the wash cycleTo terminate the ?Rinse Hold? option (in synthetic and wool
programmes only)o
Turn the programme selector to the ?? position.
Press the ?Rinse hold? button again; the load will be spun according
Select the new programme (with temperature), any options and
to the selected programme.
another spin speed if you want.
If you do not wish to spin the clothes, turn the programme selector
Press the ?Start? button again. If the ?On/Off? button is pressed, no
knob to the drain programme, after pressing the ?No Spin? button.
detergent has to added.
Cancelling a programme before the endSpin
Every programme has an automatic predefined maximum spin speed.
Turn the programme selector to the ?? position.
Press the button to select a different spin speed.
Set the programme selector to programme setting ?Drain/Spin.
If the spin speed ?0? is selected, the final spin is cancelled. The water is
Press the ?Start? button to start the ?Drain/Spin? cycle.
drained out only.
Display
Quick wash
Shows the wash cycle sequence.
For quick, economical washes. Especially suitable for small, lightly
soiled loads. This option can be used with Cotton and Synthetic
programmes. Selecting this function allows you to shorten the wash
cycle time depending on the temperature.
Note: reduce the detergent quantity.
Options
Selecting any option the indication lights up .
When the combination of programme, additional options and
temperature is not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
Power and water consumption data
Temperature LoadWaterEnergyProgramme Duration Prewash cycle increases programme duration by
approx. 15 minutes. Consumption values were
ProgrammeSelectorapprox.
measured in normalized conditions in compliance
(°C)(kg)(l)(kWh)(hours : minutes)*
with Standard IEC/EN 60 456.
Cotton905.049**1.201:56Consumption data in the home may vary with
respect to the values in the table in relation to the Cotton605.0490.952:13
water supply pressure and temperature, the load
Cotton405.0490.452:00
and the type of wash.
Synthetics602.5420.801:44* The remaining time display may differ from
Synthetics402.5420.431:34the values given in the table since it depends
on the conditions of use in the home.
Synthetics short302.0300.300:40
** To reduce the water temperature, some cold
Delicate301.5470.450:53water is added at the end of the main wash
Wool401.0580.450:48cycle, before the pump drains the water out.
Handwash302.0550.250:51
-5019 301 20104
(We reserve the right to make technical modifications)
Black process 45.0° 150.0 LPI |
ACEC
