Selecting Patches for Playing (Play Mode)
Selecting Patches for Playing (Play Mode)
HINT
Adjusting the sound
" In play mode, you can select a patch by turning
Immediately after you turn on the G9.2tt, it is always in the mode for selecting and using patches (playparameter knob 1.
In play mode, you can use the knobs on the panel
mode). The most recently used patch is automatically called up again. The various operation steps in play" When you press a foot switch whose LED is lit,
mode are described in this section. the same patch is called up once more. to adjust the basic parameters of the pre-amp
section (distortion type and intensity, EQ boost/
In play mode, the following information is shown2.To switch to a patch in another bank, cut etc.).
Panel display on the panel. use the BANK [W]/[Q] foot switches
to change the bank and then use foot 1.In play mode, select the patch.
switches 1 - 5 to select the patch.
Group name (U, u, A, b)
2.Press one of the [CHANNEL A/B] keys
Groups A and b are read-only Patch level Shows the number of the
to select the pre-amp channel A or B
groups (preset groups). Groups U parameter knob that adjusts Shows the output level setting
and u are read/write enabled the patch output level. (2 � 100) for the currently for which to make the adjustment.
groups (user groups). selected patch
Patch name
"E" symbol
BANK [W]/[Q] Foot switches
AmpDrive AmpDrive ?LVL100LVL100If the currently displayed setting
A0A 0foot switches1 - 5
�!�!Ch.AB Ch.AB �?�?BpmTpBpmTpévalue differs from the original
patch setting, the indication "E" The pre-amp section of the G9.2tt has two
Bank number (0 - 9) (for "Edited") appears. When you repeatedly press the BANK [Q] footseparate channels which allow individual settings.
Function foot switch 1/2 assignment switch, the G9.2tt switches the group/bank as
Simply pressing one of the [CHANNEL A/B]
Shows the function assigned to the function foot switch 1/2 (? p. 38).follows.
keys instantly switches the channel.
[CHANNEL A/B] keys The key for the channel (A or B) that is currently
User groups
selected for the pre-amp section is lit. HINT
You can switch between channel A and B with the
Preset groupsFUNCTION foot switch 1/2 (? p.38).
A0A1A9B0B9
3.To change the distortion type, turn
the [AMP TYPE] knob.
HINT
The [AMP TYPE] knob selects the distortion type
In play mode, you can switch the group/bank by
Effect module Keys for modules that are active in the turning the [TYPE] knob. (the amp or compact effect that is being
keys currently selected patch are lit in red. simulated). When you turn the knob, the name of
the new amp type appears on the display.
Foot switch The LED of the foot switch for the currently NOTE
1 - 5 LEDs selected patch is lit. " When using the BANK [W]/[Q] foot switches to
change banks, press and release the switch
quickly. PRE-AMP PRE-AMP �?o???�?o???
" If you keep the BANK [W] foot switch depressedFD Clean FD Clean é?�?�??é?�?�??
for more than one second, the G9.2tt switches[AMP TYPE]
to manual mode (? p. 19). Type name"E" symbolknob
" If you keep the BANK [Q] foot switch depressed
Selecting a patch for more than one second, the G9.2tt switches
to the bypass condition (effects off). If you keepHINT
This section explains how to select a patch in playthe switch depressed further, the G9.2tt" When you have changed the distortion type, the
mode. switches to the mute condition (original sound"E" symbol appears on the display, and the
and effect sound both off) (? p. 21). [STORE/SWAP] key lights up.
" If the currently displayed setting value differs
1.Press a foot switch 1 - 5 whose LED The LED of the pressed switch lights up,
from the original patch setting, the indication "E"
is not lit. indicating that a new patch has been called up.
(for "Edited") appears.
ZOOM G9.2ttZOOM G9.2tt
1415 |
ACEC
