Lint filter or water container indicator lamp
PREPARING THE LAUNDRYSELECTING A PROGRAMME & OPTIONSDAILY MAINTENANCE & CLEANING
light on:
1. Check that all fastenings are closed and that Programme and Options:Clean the lint filter at the end of every drying
? Is the lint filter clean?
pockets are empty. ? To select a programme, turn the programme cycle:
? Is the water container empty?
2. Turn the articles inside out.selector knob to the required position. The 1. Open the door.
3. Place laundry loosely in the drum to make drying indicator lamp is blinking ?? , 2. Pull the filter upwards.? Is the water container correctly positioned?
sure it doesn?t become tangled.indicating that the cycle needs to be started.3. Open the filter.? Is the heat exchanger clean?
Sort laundry as follows:4. Remove lint using a soft brush or your fingertips.Water droplets underneath the dryer:
? To select an option, press the corresponding
A) By care symbols button. The indicator light in the button 5. Close the filter.? Is the heat exchanger correctly positioned?
(on the collar or inside seam):lights up confirming that the selection has 6. Push the filter back into place.
? Has any fluff on the heat exchanger seal
been made. Empty the water container at the end of every been wiped away?
Suitable for tumble drying
? Press the option button again to cancel the drying cycle.? Has any fluff on the door seal been wiped away?
option.1. Pull the handle to remove the water container.
? Has the water container been positioned
Tumble drying with reduced drying 2. Empty the water container.
STARTING & COMPLETING A PROGRAMMEcorrectly?
intensity only. Press Gentle button.
3. Replace the water container when empty by
1. Having selected the desired programme and AFTER-SALES SERVICE
Do not tumble drypushing it completely back in place.
options, press the Start/Pause button.If, after carrying out the above checks the
TROUBLESHOOTING GUIDE
B) By amount and thickness/weightIf the laundry is not removed at the end of malfunction persists or appears again, turn the
the drying cycle, an automatic anti-crease If a fault occurs, before contacting our After-dryer off and call our After-Sales Service (refer to
Whenever the load to be dried exceeds dryer
cycle will operate for maximum 60 min. Sales Service, make the following checks to try guarantee).
capacity, separate laundry according to
The drum rotates at regular intervals, and remedy the problem:
weight (e.g. towels from thin underwear).Please specify:
preventing the laundry from creasing.
C) By type of fabricsDrying takes too long / laundry is not dry enough:? The nature of the fault.
2. On completion of the programme, set the
Cotton/linen: Towels, cotton jersey, bed and ? Was the correct programme selected?? The dryer type and model.
programme selector knob to position ?0?.
table linen made of cotton or linen.? Was the inserted laundry too wet (Washing
? The service code (the number after the word
Synthetics/Easy Care: Blouses, shirts, CHANGING A PROGRAMMEmachine spin speed less than 800 rpm? When
Service on the adhesive rating plate) on the
overalls, etc. made of polyester or When changing the programme during the drying the spinning speed is less than 800 rpm the
right-hand side when the door is open.
polyamide, as well as cotton/synthetic water container fault may occur during the
cycle, the dryer stops. The drying indicator lamp
? Your full address and phone number.
mixes.drying cycle.)?
is blinking ??.
D) By drying level? Is the lint filter dirty (filter indicator lamp on)?
To operate the new programme, press the
? Sort into: iron dry, cupboard dry, etc.? Is the heat exchanger dirty? (refer to the
Start/Pause button.
Do not tumble dry: Woollens, silk, nylon Instructions for use)
INTERRUPTING A PROGRAMME
stockings, delicate embroidery, fabrics with ? Is the ambient temperature too high?
metallic decorations, bulky items such as To interrupt the dryer during operation
The dryer does not operate:
sleeping bags, etc.
1. Set the programme selector knob to
Important: only use specific indicated dryer-Airing ??.(after a power failure and/or interruption to
the mains supply, always press the Start/
safe additives and rinse items that have been
2. Press the Start/Pause button. Pause button).
treated with stain remover thoroughly in plenty
of water before drying. Only use specific Wait at least 5 minutes before opening the ? Is the plug properly inserted into the mains
indicated dryer-safe plastic items and never door to allow the dryer to cool down.electricity socket?
dry rubber or articles contaminated with For your safety the programme stops
? Is there a power failure?
vegetable oil in the dryer.automatically if you open the door.
? Has the fuse blown?
3. To restart, after door opening, close the door
? Is the door properly closed?
and press the Start/Pause button again.
? Has the programme been selected?
? Has the Start/Pause button been pressed?
5019 307 00356 |