14E2-RU
21E2-RU
1.5kV(at1.5kV(at
??
.
.Adjusted to the above-Adjusted to the above-
, perform the following safety Checks.
2-2
TAGE SYSTEM AND PIC-
.AC outlet.)
.
A) in the case of the set. The set has been factory -
A) in the case of the set. The set has been factory - m
m
A) for the set.A) for the set.
mm
IMPORTANT SERVICE NOTES
never forget to check for such high voltage after the work.
*If there is a possibility that the high voltage fluctuates as a result of the repairing,
the high voltage completelybeam 0 beam 800 mentioned high voltage.beam 0 beam 1100 mentioned high voltage.cause excess X-ray radiation.lodged between the chassis and other metal parts in the receivercabinet backs, adjustment and compartment covers or shields, isolation resistor- ca- pacity networks, mechanical insulators etc.
Maintenance and repairing of this receiver should be done by quali- fied service personnel onlySERVICE OF HIGH VOLTURE TUBEWhen servicing the high voltage system, remove static charge from it by Connecting a 10K ohm Resistor in series with an insulated wire(such as a test probe) between picture tube dag and 2nd anode lead. (AC line cord should be disconnected from 1.Picture tube in this receiver employs integral implosion protection. 2.Replace with tube of the same type number for continued safety3.Do not lift picture tube by the neck. 4.Handle the picture tube only when wearing shatterproof goggles and after dischargingX-RAYThis receiver is designed so that any X-Ray radiation is kept to an absolute Minimum. Since certain malfunctions or servicing may produce potentially hazardous radiation with prolonged exposure at close range, the following precautions should be observed:14E2-RU 1.When repairing the circuit, be sure not to increase the high voltage to more than 25.2kV(at2.To keep the set in a normal operation , be sure to make it function on 22.7kV21E2-RU 1.When repairing the circuit, be sure not to increase the high voltage to more than 28.0kV(at2.To keep the set in a normal operation , be sure to make it function on 24.8kV3.Do not substitute a picture tube with unauthorizerd types and/or brands which mayBEFORE RETURNING THE RECEIVERBefore returning the receiver to the user1.Inspect all lead dress to make certain that leads are not pinched or that hardware is not2.Inspect all protective devices such as non-metallic control knobs, insulating fishpapers,
62W79W
Magnetic38.9MHz32.4MHz32.9MHz33.4MHz34.47MHzAll Plastics
5.0W(at Max.)
Width: 446.0mmWidth: 594.0mm Height: 465.0mm Depth: 473.0mm
Height: 333.0mm Depth: 362.0mm
16 ohms at 400 Hz
75 ohms Unbalanced
5 x 9 cm Elliptic (2 pcs)
220~ 240V AC 50/60 Hz Weight(approx): 9.2 kgWeight(approx): 21.0 kg
Self Convergence System
Quadra-Potential ElectrostaticCCIR SECAM/PAL B, G,D,K,I
E2(48.25MHz) thru E12(224.25MHz)
C1(49.75MHz) thru C12(216.25 MHz) S1(105.25MHz) thru S36(423.25HMz)
E21(471.25MHz) thru E69(855.25MHz) C13(471.25MHz) thru C57(863.25MHz) S37(431.25MHz) thru S41(463.25MHz)
2-1
............................................................
..............................................................
...........................................................
..................................................................................
SPECIFICATIONS..............................................................................................................................................................................................................................................................................................................
Specifications are subject to change without prior notice.
Convergence.................................................................Focus......................................................................Sweep DeflectionIntermediate Frequencies Picture IF Carrier Sound IF Carrier Frequency 6.5MHz.............................................................................................. 6.0MHz.............................................................................................. 5.5MHz.............................................................................................. Colour Sub-Carrier FrequencyPower Input......................................................................Power Consumption 14E2-RU...................................................................................................... 21E2-RU......................................................................................................Audio Power Output RatingSpeaker Size................................................................................ Voice Coil ImpedanceAerial Input Impedance VHF/UHF..........................................................................Receiving SystemTuner Ranges VHF-Channels UHF-ChannelsDimensions 14E2-RU................................................................................... 21E2-RU...................................................................................Cabinet material
2 |
ACEC
SHARP
