EN 205.LC03EService Modes, Error Messages, and Repair Tips
2. Select ?LOCK? (with the RC)
3. Set to ?OFF?
1 TYPE: 17PF9945/012 HRS:0029 CSM1?Line 10: ?NOT PREFERRED?. Indicates that the current
2 SWID: LC03E21-1.11 S317 1.03
channel is not in the preferred channel list (by default, all
3 ERR : 0 0 0 0 0 0 0
4 OPT : 79 254 14 56 128 000channels are skipped. A channel can be added as a
5selected channel to the list of preferred channels:
6 SYSTEM: WEST EUR11 SOURCE : 51. Select ?INSTALL? menu
7 NO SIGNAL12 SOUND : MONO
2. Select ?CHANNEL EDIT?
8 TIMER ON13 VOLUME : 26
9 CHANNEL BLOCKED14 BALANCE: 13. Select ?ADD/DELETE?
10 NOT PREFERRED15 COLOUR : 504. Set to ?ADD? with the left/right cursor keys
?Line 11: ?SOURCE?. Indicates which SOURCE is installed
for this preset: EXT1, SVHS2, EXT2, or Tuner.
?Line 12: ?SOUND?. Indicates which sound mode is installed
CL 36532023_085.eps
for this preset: Mono, NICAM, Stereo, L1, L2, SAP, Virtual,
140403
or Digital.
?Line 13: ?VOLUME?. Value indicates level at entry CSM.
Figure 5-3 CSM 1
?Line 14: ?BALANCE?. Value indicates level at entry CSM.
?Line 15: ?COLOUR?. Value indicates level at entry CSM.
The Customer Service Menu (CSM1) shows the following
information:
?Line 1: ?TYPE: 99XX9999/99XHRS: nnnn?. TYPE: type-1 TYPE: 17PF9945/012 HRS:0029 CSM2
version/model of the set (i.e. 17PF9945/12). HRS: 2 SWID: LC03E21-1.11 S317 1.03
Hexadecimal counter of operating hours. (Standby hours 3 ERR : 0 0 0 0 0 0 0
4 OPT : 79 254 14 56 128 000
are counted as operating hours).
5
?Line 2: ?SWID: AAAABBC-X.YYS3DDE.FF?. SWID: 6 BRIGHTNESS: 5011
(Software identification of the main micro controller on TV-7 CONTRAST : 56 12
Board and Scaler board) See paragraph ?Service 8 HUE : 5013
914
Alignment Mode (SAM)?. Details on available software
1015
versions can be found in the chapter ?Software Survey? of
the publication ?Product Survey - Colour Television?.
?Line 3: ?CODES: xx xx xx xx xx xx xx ?. Error code buffer
(see paragraph ?Errors?). Displays the last 7 errors of the CL 36532023_086.eps
140403
error code buffer.
?Line 4: ?OPT xxx xxx xxx xxx xxx xxx xxx xxx?. Option
bytes. Option bits control the software and hardware Figure 5-4 CSM 2
functionality of the chassis. An option byte or option
number represents 8 of those bits. Each option number is The next Customer Service Menu (CSM2) shows the following
displayed as a decimal number between 0 and 255. The information:
set may not work correctly when an incorrect option code ?Line 6: ?BRIGHTNESS?. Value indicates level at entry
is set. See chapter 8 for more information on correct option CSM.
settings?Line 7: ?CONTRAST?. Value indicates level at entry CSM.
?Line 6: ?SYSTEM: EUROPE/WEST EUR/EAST EUR/UK/?Line 8: ?HUE?. Value indicates level at entry CSM.
FRANCE?. Indicates which colour and sound system is ?Line 9: ?HOTEL MODE ON?. Indicates that the Hotel mode
installed for this preset as defined in the Manual INSTALL has been activated.
menu:
- PAL BG
5.3Errors
- PAL I
- PAL DK
- SECAM BG5.3.1 Error code buffer
- SECAM DK
- SECAM LL?The error code buffer contains all errors detected since the last
?Line 7: ?NO SIGNAL?. Indicates that the set is not receiving time the buffer was erased. The buffer is written from left to
an ?ident? signal on the selected source.right. When an error occurs that is not yet in the error code
- No or bad antenna signal; connect a proper antenna buffer, the error is written at the left side and all other errors
signalshift one position to the right.
- Antenna not connected; connect the antenna
- No channel / preset is stored at this program number; The error code buffer will be cleared in the following cases:
go to the INSTALL menu and store a proper channel at - By activating the CLEAR ERRORS function in SAM menu.
this program number- By transmitting 0-6-2-5-9-9 with the normal RC.
- The tuner is faulty (in this case the CODES line will - By transmitting the commands ?DIAGNOSE 99 OK? with
contain number 13); check the tuner and replace/repair the DST (RC7150) or with ComPair.
if necessary- Automatically reset if its contents has not changed for 50
Note: On some models, BLUE MUTE is displayed (if the BM hours.
option is ON) when no signal is received.
?Line 8: ?TIMER ON?. Indicates that the sleep timer is By leaving SDM or SAM with the mains switch, the error buffer
activated. Complaints that may be caused by the activation is not reset.
of the sleep timer.
?Line 9: ?CHANNEL BLOCKED?. Indicates that one or more Examples:
channels are locked except the selected channel. ERROR: 0 0 0 0 0 0 0 : No errors detected
Complaints that may be caused by locked channels:ERROR: 6 0 0 0 0 0 0 : Error code 6 is the last and only
- TV cannot be switched on from standby with the local detected error
keyboard buttonsERROR: 9 6 0 0 0 0 0 : Error code 6 was first detected and error
- ?P+? and ?P-? buttons on local keyboard do not functioncode 9 is the last detected (newest) error
To disable the LOCK feature:
1. Select ?FEATURE? menu (with the Remote Control) |
ACEC
PHILIPS
