ifu_az1836_latam_eng 2006.8.23 11:38 AM Page 7
Safety & Maintenance (See !)Troubleshooting
Safety information CD player and CD handling If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
Y Place the set on a hard, flat and stable surfaceY If the CD player cannot read CDs correctly,
so that the system does not tilt.use a cleaning CD to clean the lens beforeWARNING:Do not open the set as there is a risk of electric shock.Under no cir-
taking the set to repair.cumstances should you try to repair the set yourself,as this will inval-
Y Do not expose the set, batteries, CDs toidate the guarantee.
humidity, rain, sand or excessive heat causedY The lens of the CD player should never be
by heating equipment or direct sunlight.touched!No sound/ powerSound skips during MP3 playback
Y The apparatus shall not be exposed to Y Sudden changes in the surrounding � Volume not adjusted� MP3 file made at compression level exceeding
320kbps
dripping or splashing.temperature can cause condensation on theY Adjust the VOLUME
Y Use a lower compression level to record CD
lens of your CD player. Playing a CD is then� Power cord not securely connected
Y Adequate ventilation with a minimum gap of
not possible. Do not attempt to clean theY Connect the AC power cord properlytracks into MP3 format
15 cm between the ventilation holes and sur-
lens but leave the set in a warm environment� Batteries dead/ incorrectly inserted� Disc damaged or dirty
rounding surfaces is necessary to preventY Insert (fresh) batteries correctlyY Replace or clean disc.
until the moisture evaporates.
heat build-up.� Disc contains non-audio filesNote:
Y The ventilation should not be impeded byYAlways close the CD door to avoid dust onY Insert a suitable disc or press or once orDRM-protected WMA disc is not supported.
covering the ventilation openings with items,the lens.more skip to an audio track, instead of the data
such as newspapers, table-cloths, curtains, etc..YTo clean the CD, wipe in a straight line fromfiles.The USB device doesnOt play on my
the center towards the edge using a soft,AZ1836
Y No objects filled with liquids, such as vases,Display does not function properly/No
lint-free cloth. Do not use cleaning agents as
shall be placed on the apparatus.reaction to operation of any of the � It is not set in the USB mode.
they may damage the disc.controlsY Press CD/USB to select USB mode.
Y No naked flame sources, such as lighted can-
dles, should be placed on the apparatus.Y Never write on a CD or attach any stickers� Electrostatic discharge� The device is not securely connected to AZ1836Os
to it.Y Switch off and unplug the set. Reconnect after aUSB port.
Y The mechanical parts of the set contain
few seconds.Y Re-connect the device, and make sure that the
self-lubricating bearings and must not be oileddevice is powered on.
or lubricated.no indication
� The device is not supported by AZ1836,or the audio
YTo clean the set, use a dry cloth. Do not use� It is set in the USB mode.file format stored on the device is not supported by
any cleaning agents containing alcohol,Y Press CD/USB to select CD mode.AZ1836.
ammonia, benzene or abrasives as these may� No disc inserted Y Use a compatible device/ playable audio file
harm the housing.Y Insert a suitable disc format.
� Disc badly scratched or dirty
Y Replace/clean CD (See Maintenance)The disc file cannot be recorded to the
� CD-R(W) is blank or the disc is not finalized.USB device
Y Use a finalized CD-R(W)
� You stop recording when the MP3 or WMA file you
� Laser lens steam up
want to record is still playing.
YWait until lens has cleared.Y Select record-one mode to record, or stop
Note:recording only when the playback of MP3 or
Make sure the CD is not encoded withWMA file is wholly completed.
Copyright protection technologies,as some� The memory of the USB device runs out.
do not conform to the Compact Y Delete some unwanted files on the USB device to
Environmental information
Disc standard.free some memory, or use another USB device of
All unnecessary packaging material has been omitted.The packaging can be easily separatedsufficient free memory to record.
The disc skips tracks
into three materials: cardboard, polystyrene and plastic.� The name of a MP3 or WMA file on the disc is
� Disc damaged or dirty
identical to the one of a file on the USB device.
Your set consists of materials which can be recycled if disassembled by aY Replace or clean discY Change to a different name for the file on the
� Shuffle or program is active
specialized company. Please observe the local regulations regarding theUSB device.
Y Switch off shuffle/program
disposal of packaging, dead batteries and old equipment. |
ACEC
PHILIPS
