SHARP CD-BP1700W Repair Manual

CD-BP160W/180W/1500W/1700W
).
?
is used, connect the unit using the AC plug adaptor sup-
­
AM/FM interval (span)Press the ON/STAND-BY button to enter the stand-by mode.Set the SPAN SELECTOR switch to "50/9" for 9 kHz AM interval (50 kHz FM interval), and "100/10" for 10 kHz AM interval (100 kHz FM interval).Whilst pressing down the button and the X-BASS/DEMO button, hold down the ON/STAND-BY button for at least 1 second."CLEAR AL" will appear.The operation explained above will erase all data stored in memory including clock and timer settings, and tuner and CD presets.Connecting the AC power leadPlug the AC power lead into a convenient AC socket, after any connections.Unplug the AC power lead from the AC socket if the unit will not be in used for a prolonged period of time.Never use a power lead other than the one supplied. Use of a power lead other than the one supplied may cause an electric shock or fire. AC Plug Adaptor
nThe International Telecommunication Union (ITU) has established that member countries should maintain either a 10 kHz or a 9 kHz interval between broadcasting frequencies of any AM station. The illustration shows the 9 kHz interval zones (regions 1 and 3), and the 10 kHz interval zone (region 2). Before using the unit, set the SPAN SELECTOR switch (on the rear panel) to AM tuning interval (span) of your area.To change the tuning zone:123lCaution: lnCheck the setting of the AC voltage selector located on the rear panel before plugging the unit into an AC socket. If necessary, adjust the selector to correspond to the AC power voltage used in your area.Selector adjustment: Turn the selector with a screwdriver until the appropriate voltage number appears in the window (110V, 127V, 220V or 230V - 240V AC).Notes: llllIn areas (or countries) where an AC socket as shown in illustra- tion plied with the unit, as illustrated. The AC plug adaptor is not included in areas where the AC wall socket and AC power plug can be directly connected (see illustration Note for users in Australia and New Zealand: An AC plug adaptor is not supplied if the lead has an Australian Standard plug.
12
To an AC socket
220V
(Continued)
The 24-hour display will appear. The 12-hour display will appear. The 12-hour display will appear.
?
?
?
Press the ON/STAND-BY button to enter the stand-by mode.Press the CLOCK button.Within 5 seconds, press the MEMORY/SET button.Press the TUNING/TIME ( or ) button to select the time display mode."0:00" (0:00 - 23:59) "AM 0:00" (AM 0:00 - PM 11:59) "AM 12:00" (AM 12:00 - PM 11:59)Note that this can only be set when the unit is first installed or it has been reset.Press the MEMORY/SET button.Press the TUNING/TIME ( or ) button to adjust the hour.Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously.When the 12-hour display is selected, "AM" will change auto- matically to "PM".Press the MEMORY/SET button.Press the TUNING/TIME ( or ) button to adjust the minutes.Press the TUNING/TIME ( or ) button once to advance the time by 1 minute. Hold it down to change the time in 5 minute intervals.The hour setting will not advance even if minutes advance from "59" to "00".Press the MEMORY/SET button.The clock starts operating from "0" second. (Seconds are not displayed.) And then the clock display will disappear after a few seconds.The time display will appear for about 5 seconds.The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power lead is disconnected. If this happens, follow the procedure below to change the clock time.Press the CLOCK button.Within 5 seconds, press the MEMORY/SET button.Perform steps 6 - 9 above.Perform steps 1 - 2 in the section "RESETTING THE MICRO- COMPUTER".Perform steps 1 - 9 above.
In this example, the clock is set for the 24-hour (0:00) system.1234l56ll78ll9lTo see the time display:Press the CLOCK button.lNote: lTo change the clock time:?­?To change the time display mode:?­
AM 12:00
AM 0:00
MEMORY/SET
0:00
CLOCK
TUNING/ TIME ( )23456789
SETTING THE CLOCK (Main unit operation)ON/ STAND-BY
� 7 �