CD-BA120/125
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the
following safety checks.
1. Inspect all lead dress to make certain that leads are notVTVM
pinched or that hardware is not lodged between the chassisAC SCALE
and other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,1.5k ohms
cabinet, terminal board, adjustment and compartment covers10W
or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage
current in the following manner.
0.15 ? F
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5k ohm, 10 watt resistorCONNECT TOTEST PROBE
TO EXPOSED
paralleled by a 0.15mF capacitor in series with all exposedKNOWN EARTH
METAL PARTS
metal cabinet parts and a known earth ground, such asGROUND
conduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,
sensitivity to measure the AC voltage drop across theAll check must be repeated with the AC line cord plug connection
resistor (See diagram).reversed.
* Connect the resistor connection to all exposed metal partsAny reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.
having a return path to the chassis (antenna, metal cabinet,AC.) or more is excessive and indicates a potential shock
screw heads, knobs and control shafts, escutcheon, etc.)hazard which must be corrected before returning the audio
and measure the AC voltage drop across the resistor.product to the owner.
SPECIFICATIONS
CD-BA120/125
l Generall Cassette deck section
Power source:AC 120 V, 60 HzFrequency response:50-14,000 Hz (Normal tape)
Power consumption: 35 WSignal/noise ratio:55 dB (TAPE 1, playback)
Dimensions:Width; 10-5/8" (270 mm)50 dB (TAPE 2, recording/playback)
Height; 11-13/16" (300 mm)Wow and flutter:0.3 % (WRMS)
Depth; 14-11/16" (373 mm)
Weight:10.6 lbs. (4.8 kg)
l Amplifier sectionCP-BA120/125
Output power:10 watts minimum RMS perl Speaker section
(Except for Canada)channel into 8 ohms from
Type:4" (10 cm) full-range speaker
100 Hz to 20 kHz, 10 %
Maximum input power:20 W
total harmonic distortion
Rated input power: 10 W
Output power:RMS; 20 W (10 W + 10 W)
Impedance:8 ohms
(For Canada)(10 % T.H.D.)
Dimensions:Width; 8-11/16" (220 mm)
Output terminals: Speakers; 8 ohms
(CD-BA120)Headphones; 16-50 ohmsHeight; 11-13/16" (300 mm)
(recommended; 32 ohms)Depth; 7-1/16" (180 mm)
Weight:4.4 lbs. (2.0 kg)/each
Output terminals: Front speakers; 8 ohms
(CD-BA125)Rear speakers; 16 ohms
Headphones; 16-50 ohms
(recommended; 32 ohms)
GBOXS0042AWM1
l Rear speaker section (CD-BA125 Only)
l Compact disc player section
Type:3-3/32"(8 cm) full-range speaker
Type:3-disc multi-play compactMaximum input power:5 W
disc playerRated input power: 10 W
Signal readout:Non-contact, 3-beam semi-Impedance:16 ohms
conductor laser pickupDimensions:Width; 6" (150 mm)
D/A converter:1-bit D/A converterHeight; 6" (150 mm)
FrequencyDepth; 3" (78 mm)
response:20 - 20,000 HzWeight:0.9 lbs. (0.4 kg)/each
Dynamic range:90 dB (1 kHz)
Specifications for this model are subject to change without
l Tuner sectionprior notice.
Frequency range:FM; 87.5-108 MHz
AM; 530-1,720 kHz
� 2 � |
ACEC
SHARP
