The hood may be supplied with a standard plug indicated on the label affixed inside the hood house voltage corresponds with the voltage Before completing any connection, make sure theElectric connectionto vent the air easily from the room to the outside. slightly slanted (about 10 diameter. In the horizontal runs the duct must be the fumes outlet duct must be 100-120 mm. in mixed-fuel burners. In the vented exhaust version cm. above electric burners or 70 cm. above gas or When installed. the hood must be not less than 60Installationinto place on the conveyor (fig. 6) N rotate in clockwise direction (fig. 5). N There are two carbon filter models available:Lever grid. The air is recycled into the room through the frontInternal recycle system (filtering)nal. This fits on the coupling ring (Fig. 4) A non-return fume valve is available as an optio-Lever E open the hole on the conveyor by pulling the tabs Important: outlet (fig. 1). outlet selected. Use cover To connect the pipe fit the coupling ring at the top The appliance is fitted with 2 exhaust outlets: oneExternal exhaust systemY Recycle system (filtering) Y External exhaust system Two systems are available:Use
(fig. 2).GB
Rectangular: Circular:
FF
: in position : in position
OA�
When using the rear exhaust outlet
with bayonet attachment N
and the other at the back
fits on the frame G and snaps
FA
(fig. 3). (fig. 3).
°OD�
) and directed upwards
to close the unused
OC�
OB�
in the
.
N No food must be cooked flambeau underneathN If the hood is run at the same time as anAttentionhood (see electrical sketches enclosed) . switches, which change according to the type of front part of the appliance there are the control to ensure that all odours are extracted. On the it running for approximately 15 minutes afterwards minutes before starting cooking and then to leave It is advisable to switch on the extractor hood a fewUsing the hoodN Now hang the hood (holes N Fit 2 5x45 screws on N Fit 3 0,8 mm wall plugsN Make 3 8 mm ? holes on the wall. 2 on N Fit the template to the wallFixing to the wallN Fit the 4 4.2x35 screws supplied, from insideN Make holes at the bottom of the cabinet usingFixing to the cabinetinstructions. caused by the userOs failure to observer the above The manufacturers are not liable for any problems between contacts of not less than 3 mm. conforming to regulations with an opening distance plug conforming to regulations or a two-pole switch If the appliance is not fitted with a plug, either fit a socket. and if so connect it to a correspondingly standard
the hood.boxes or by other technical devices. through air-recycling doors, windows or wall sure there is an air inlet .which may be provided gas from coming back into the room, make For safe operation and to prevent discharged combustion. ambient air the burners or fireplace need for hood, when it exhausts the air, removes the water heaters, etc.), be careful, because the example gas, diesel, coal or wood heaters, ambient-air dependent burner or fireplace (forfrom inside the cabinet (fig. 8). screws and fit the third 5x45 screw in hole Icompletely1 hole on any of points (fig.7). the cabinet in the holes on the appliancethe template supplied
I, as required.
H
HNdo not tighten
). Tighten the 2
H
, and
Circular filter: This is not washable and can not be reused.Carbon Filterstop To dismount the filter, open the grid and removetoo with warm water and biodegradable detergent. When cleaning the grease filter, wash the grate4) The life of the metal filter is practically unlimited3) The tin synthetic filter (thickness about 1 mm.)2) The thin synthetic filter (thickness about 1Wash it in warm water a biodegradable detergent.1) The synthetic filter (thickness about 12-15 mm) saturation indicator, and metal. with saturation indicator, thin synthetic without in four different versions: synthetic, thin synthetic It is installed in the exhaust grate and is available particles. The grease filter traps the suspended greaseGrease filterN To remove, pull forward from the right handN Open the latch Grid Openingdisconnect the hood from the electricity. Before performing any maintenance operation,MaintenanceN The manufacturers refuse liability for damageN The hood must not be connected to fuel exhaust
reinstalling It. tic filter once a month and allowed to dry before and should be washed the same as the synthe-two months with normal use. without saturation indicator is replaced everyon the bottom. mm.), is changed when the top coloring appearsLet it dry without wringing .replaced after 5 or 6 washinings. in normal use is washed once a month andside and unhook.(fig. 9)failure to observe the above instructions. to the hood or its catching on fire because ofetc). flues (boilers, heating systems, water heaters,because cooking oil could flare up. When frying foods, never leave the pan alone never use an open flame under the hood. for the filters and could cause fires. Therefore, The use of an unprotected flame is dangerous
M
(fig. 9).
L
and rotate the grid downwards
television noise standards. This appliance meets 87/308 EWG radio andabrasives. detergents. Never use products containing moistened with denatured alcohol or neutral liquid To clean the outside of the hood use a clothCleaningN Before calling for repair service because theN Always replace burn-out bulbs with olive-sha- N Remove the grate. N Disconnect the hood from the electricity.Changing the bulbsthese instructions. cause fires. Therefore, we recommend observing pliance and changing and cleaning the filters may Failure to observe the rules for cleaning the ap-Attention(fig.6). N push the stops Dismounting the filter: N replace every 6/8 months Rectangular filter: N rotate in anti-clockwise direction Dismounting the filter: N replace every 3/4 months for normal use
screwed in tightly. hood fails to light up, make sure the bulbs areped max 40 Watt (E14) bulbs.
N
in and pull the filter down |
ACEC
ELECTROLUX
