CROSSLEE CL767B-031276715501 Instruction Manual

10698 A3 45689 GB Broadsht 21/11/02 3:22 PM Page 1
INSTALLATIONOPERATION
Open the door.NEVER SWITCH THE DRYER OFF AND LEAVE A
INSTALLATION OF THE DRAIN KIT6. Move the machine into its working position with the drain
HOT LOAD IN THE DRUM.
hose inserted into the waste pipe.Load clothes loosely into the drum.
Your dryer may be supplied with a drain kit. This can be fitted
so that the condensed water can be emptied into a waste-pipe7. Position the machine in a well ventilated room. Make sure
Load sheets first, starting with one corner.
that the air inlet at the front is not blocked.AFTER REMOVING THE DRIED CLOTHES:
instead of the water bottle in the machine. If a kit is not
supplied, one can be obtained from your dealer.Close the door.ALWAYS CLEAN THE FILTER.
The illustration shows the minimummFailure to do so could cause the safety cut-out to operate.
Dry your hands.
space required by the dryer and the50mm
600m
position of the waste-pipe within this
Check that the timer is in the �0O position.
space and behind the dryer. If a trap� Pull the filter upwards and away from








is fitted it must not obstruct the airPlug in the machine.






the appliance.








inlet at the back of the dryer.















Select correct heat position (see programme chart on control� Remove any threads or fluff by hand or
The waste pipe can be positioned























on either side of the dryer.panel for recommendations).

























with a soft brush.
L











JK
If the waste pipe is used by both theSet the timer to the required time setting (see progr









amme chart on� Slide the filter back.
dryer and a washing machine then
control panel for recommendations). Then press start button.�W ash the filter occasionally in detergent
its diameter must be large enough
FINAL INSTALLATION









solution using a soft brush to remove
to contain both hoses - 1.5� bore









The drum will begin rotating. Reversing drum models will stop
















small particles.
(38mm) minimum.Push the filter into its operatingevery few minutes to rotate in the reverse direction for a short

































position as shown in the diagr





am.










1. Unscrew the plastic nJ from the connector at the toput , reartime.
of the machine. Remove and discard the plastic disc.If yKeepou wish to change the side on
the rubber washer K.which your door opens, see theShould the clothes become dry before the cycle has finished, or if
ALWAYS EMPTY THE WATER BOTTLE
instructions on the back page.an excessive programme time has been selected, the drum will
2. Push the flanged tube L into the connector as shown until
the flange is fully seated.Remove any dust by wiping the drumcontinue to rotate while the thermostat will automatically switch
� Open the door, pull out and empty the
and door with a damp cloth. Any initialthe heater off to prevent over-drying and save energy.
3. Push the free end of the hose through the threaded end ofbottle.
smell from the heater should
the nut and pull through so that the flange of the plasticIf the door is opened during a cycle the dryer will stop. To restart,
disappear after the first period of� Replace the bottle ensuring that it is
elbow, at the other end of the hose is seated against the
heating.close the door. When drying large items such as sheets, wepushed all the way in - if it is not, the
inside of the nut.
Position the tumble dryer so that thesuggest you periodically stop the dryer to redistribute the load.dryer will not operate.
4. Insert the rubber wKasher .
plug remains accessible after
There is an automatic 12 minute cool down period at the end of� If the dryer is connected to a drain there
5.Screw the nut onto the connector on the back of the machineinstallation. Do not block the vent at
every cycle, during which the heater is switched off. This helps tois no need to empty the bottle but it must
and position the elbow so that the hose will fit into the wthe front of the draste-yer, as this will
minimise creasing.be correctly fitted to the machine.
pipe. Shorten the hose if necessary. Tighten the nut.impair the working of the machine
THE CONTROLSPREPARATIONADDITIONAL INFORMATION
Check care labels inside the garments.
ANY PROBLEMSDrain Hose Kit
CARE LABELS YOU MAY FIND ON YOUR To enable your dryer to be connected to a drain to remove the
If the clothes are not dryafter normal drying time:
FABRICSneed to empty the water bottle.
� Check that you used the correct heat setting.
� Check that you have not set the timer within a cool down
DSuitable for tumble drying
BAperiod.
C
� Check that the lint filter has been cleaned. A blocked filter
Tumble dry using full heat
will restrict the airflow.TECHNICAL DATA
Tumble dry using half heat� Check that the condenser unit and associated duct work are
clean. If blocked these will restrict the airflow.OVERALL DIMENSIONS:
Do not tumble dry� Check that your dryer is heating - below the door to the leftHeight: 85 cm
side, should feel warm to the touch after the first 10-15Width: 59.5 cm
BDo not tumble dry woollen or wool mixture articles unless theminutes of its programme. Failure to heat may indicate theDepth: 58 cm
A
Carticle is labelled to be suitable due to a possibility of shrinkagesaf.ety cut-out has operated. To reset, simply press the red
button at the rear of the machine. If it has operated then a
Roll dripping wet articles in a towel to remove excess water.
MAXIMUM DRY WEIGHT LOADS:
sharp Oclick� will be heard. This cut-out only operates if the
Place delicate articles e.g. tights, scarves, inside a pillowcase.Cotton 6kg
airflow is severely restricted so make sure the filter is clean
To avoid the need to iron easycare polyester/cotton items it isand that all other restrictions are removed before re-star(for minimting.um creasing 2kg)
better to only dry small loads (i.e half fill drum).If the cut-out continues to operate after checking the aboDelicates 2kg ve
points, you should contact your service agent.
It is better to dry small and large articles together.
CBA� Check that the machine has the correct weight load in the
We suggest a fabric conditioner to be used to reduce staticFor electrical ratings see plate on back of dryer.
drum before starting the appliance.
A. THE TIMERelectricity.For Model No. see serial plate inside door (needed when
Select the required dryer time based on the recommendations
Do not overload the dryer or dry large bulky items such as duvetsIf your machine does not workcheck the following beforerequesting service).
on the control panel.
or sleeping bags as it is important that the airflow through thecalling a service engineer:Room temperature range 5uC to 30uC.
B. HEAT SWITCH(ES)
dryer is not obstructed.� Check that there is a supply of electricity.
Select the required heat setting based on the recommendationsYour washing machine should have a spin speed of not less
on the control panel.Do not place items contaminated with inflammable substances in� Check that the door has been properly closed and thethan 800rpm.
C. BOTTLE FULL NEONthe dryer, such as petrol, cleaning solvents, cooking oil, fat, ormachine is switched on.
This will light when the bottle needs emptying or when it ishair lacquer. These can cause fires. For the same reason, do not� Check that the water bottle has been withdrawn from, and
incorrectly inserted.
dry rubber, foam rubber, plastic or paper.replaced into the machine.
D. START BUTTON
� Check the plug internal connections.
Press start button after selecting the required drying time.