SHARP CPC470H Repair Manual

CD-C470H,C470E,C480H/CP-C470H,C470E,C480H
OPERATION MANUAL
Replace the batteries if control distance decreases or oper- ation becomes erratic.Periodically clean the transmitter LED on the remote control and the sensor on the main unit with a soft cloth.Exposing the sensor on the main unit to strong light may interfere with operation. Change the lighting or the direction of the unit.Keep the remote control away from moisture, excessive heat, shock, and vibrations.To erase all of the stored memory contents (clock and timer settings, tuner and CD presets).If the display is not correct.If the operation is not correct.To erase the tuner preset memory, see "To erase all of the contents of preset memory" on page 19.Press the ON/STAND-BY switch to enter the stand-by mode.Press the VOLUME button, the TUNING/TIME button and the ON/STAND-BY switch all at the same time. Hold them down for at least 1 second.
Notes concerning use:Reset the microcomputer under the following conditions:Note:12
2
15
15
0.2 m - 6 m (8" - 20')
2
1,2
PREPARATION FOR USERESETTING THE MICROCOMPUTER
The 12-hour display will appear. The 12-hour display will appear. The 24-hour display will appear.
??
?
"AM 12:00" (AM 12:00 - PM 11:59) "AM 0:00" (AM 0:00 - PM 11:59) "0:00" (0:00 - 23:59)
Set the ON/STAND-BY switch to STAND-BY.Press the CLOCK button.Within 5 seconds, press the MEMORY/SET button.Press the TUNING/TIME ( or ) button to select the time display mode.Press the MEMORY/SET button.Press the TUNING/TIME ( or ) button to adjust the hour.Press the TUNING/TIME button once to advance the time by 1 hour. Press for more than 0.5 seconds to advance continu- ously.When the 12-hour display is selected, "AM" will change auto- matically to "PM".Press the MEMORY/SET button.Press the TUNING/TIME ( or ) button to adjust the minutes.Press the button for at least 0.5 seconds to change the time in 5-minute intervals.The hour setting will not advance even if minutes advance from "59" to "00".Press the MEMORY/SET button.The clock starts operating from "0" seconds. (Seconds are not displayed.)In the event of a power failure or when the AC power lead is disconnected, the clock display will go out. When the AC power supply is restored, the clock display will flash on and off to indicate the time when the power failure occurred or when the AC power lead was disconnected.If this happens, follow the procedure below to change the clock time.The time display will appear for about 5 seconds.Set the ON/STAND-BY switch to STAND-BY.Press the VOLUME button, the TUNING/TIME button and the ON/STAND-BY switch all at the same time. Hold them down for at least 1 second.Perform steps 1 - 9 above.The operation explained above will erase all data stored in memory, such as clock and timer settings, tuner and CD pres- ets.
123456789Note:To see the time display: (When the power is ON)Press the CLOCK button.To switch the time display mode:123Note:
AM 0:00
AM 12:00
0:00
In this example, the clock is set for the 24-hour (0:00) system.
ON/ STAND-BYCLOCKMEMORY/ SETTUNING/TIME ( )23456789
When the unit is in the demonstration mode, press the DEMO button to enter the clock mode.Press the MEMORY/SET button.Perform steps 6 - 9 above.Press the CLOCK button.Within 5 seconds, press the MEMORY/SET button.Perform steps 6 - 9 above.
SETTING THE CLOCK
To change the clock time:When the ON/STAND-BY switch is set to STAND-BY.12When the ON/STAND-BY switch is set to ON. 123
� 6 �