2. TEST MODE
2.1 HOW TO ENTER THE TEST MODE(5) Pause
There are three ways of entering the test mode.1. It becomes pause condition by pressing [CX] (0E) key of the
remote control unit in the play.
1. Short-circuit the terminals (TP6006 and TP6007) for test mode
entry located at the side of the system control IC (IC601) of DVDM2. Pause ON/OFF changes alternately by pressing [PAUSE] (18)
key in the play.
ASSY, and turn the power on.
2. Press the [ESC] key and the [TEST] key on the Service Remote
Control [PIGGF1067] while the player is in the power on mode.(6) Search Address Input Entry
3. Connect a personal computer to the RS232C terminal (CN106)It becomes the address input mode when [+10] key (1F) is pressed.
and input the entry command (TE) of the test mode from the(indication for the most significant digit : > )
personal computer.Indicate the last address as the initial condition in this time.
Note: FL indication and LED come all to light until key operationOnly in case of DVD, addition search (indication for the most
is done when entering the test mode.significant digit : + ) and subtraction search (indication for the most
significant digit : � ) are able to select in order by pressing [+10]
2.2 RELEASE THE TEST MODEkey continuously.
The address where input value was added to the present address is
There are three methods to escape the test mode.
make to search with addition search.
The address where input value was subtracted to the present address1. Turn the power off.
2. Press [ESC] key of the remote control unit. At this time, reset it
is make to search with subtraction search.for a while.
In case of CD is only absolute time search.
Also address clear and release from the address input mode are able3. Connect a personal computer with the RS232C terminal (CN106),
and input normal mode entry command (NE) from the personal
to perform by 2 steps by pressing [CLEAR] (45) key.computer.
(7) Search Address Input2.3 THE EXPLANATION OF EACH
Press [0] to [9] keys of the remote control unit.
FUNCTIONSet up the address by the hexadecimal number with DVD.
The function that can be operated in the test mode is as the following.When [PROGRAM] (4C) key is pressed in the address input mode,
input mode changes to hexadecimal number input (Indicates "*"Use a LD remote control unit in the test mode.
mark), and [1] to [6] keys are input as [A] to [F].
At this time, [7], [8], [9] and [0] keys are not accepted.
(1) Door Open/Close
Also the hexadecimal number input and the decimal number input
can be changed with toggle.1. Press [REPEAT A-B] (48) key of the remote control unit.
2. Press [OPEN/CLOSE] key of the player from the stop condition.
(8) Search Practice
(2) Stop
1. Press [CHP/TIM] (13) key of the remote control unit.
Practice the on screen no playback (Doesn't demultiplex) after1. Press [REPEAT] (44) key of the remote control unit.
2. Press [STOP] key of the remote control unit or the player from
the search with DVD.the stop condition.
2. Press [PLAY] (17) key of the remote control unit.
Practice the on screen playback (demultiplex exists) after the
(3) Play 1 (Demultiplex exist which it tries to outputsearch with DVD.
the playback screen)
1. Press [PLAY] (17) key of the remote control unit.(9) Tracking Open
Y DVD rise up at the tracking close. Playback screen may not1. Press [STEP FWD] (54) key of the remote control unit in the play
appear because the NAVI information isn't read in the test mode.condition.
2. Switch the open/close by pressing [PLAY] key of the remote
(4) Play 2 (Demultiplex is absent which performingcontrol unit or the player during the play (CD only).
trace only)
1. Press [TV/LDP] (0F) key of the remote control unit.
Y Perform only tracing with DVD, and there are no video and
audio output.
6 |
ACEC
HITACHI
