Water Pressure
Electrical Requirements
A cold water supply with water pressure of between 30 and
120 psi (207 - 827 kPa) is required to operate the water dispenser WARNING
and ice maker. If you have questions about your water pressure,
call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 - 827 kPa)
If a reverse osmosis water filtration system is connected to your
Electrical Shock Hazardcold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).
Plug into a grounded 3 prong outlet.
If the water pressure to the reverse osmosis system is less than
Do not remove ground prong.40 to 60 psi (276 - 414 kPa):
Check to see whether the sediment filter in the reverse
Do not use an adapter.
osmosis system is blocked. Replace the filter if necessary.
Do not use an extension cord.Allow the storage tank on the reverse osmosis system to refill
after heavy usage.Failure to follow these instructions can result in death,
fire, or electrical shock.If you have questions about your water pressure, call a licensed,
qualified plumber.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.Connect the Water Supply
Recommended Grounding MethodRead all directions before you begin.
A 115 Volt, 60 Hz., AC only 15 or 20 amp fused, grounded IMPORTANT: If you turn the refrigerator on before the water line is
electrical supply is required. It is recommended that a separate connected, turn the ice maker OFF.
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an Connect to Water Line
extension cord.
NOTE: Before performing any type of installation, cleaning, or 1. Unplug refrigerator or disconnect power.
removing a light bulb, turn the control (Thermostat, Refrigerator or 2. Turn OFF main water supply. Turn ON nearest faucet long
Freezer Control depending on the model) to OFF and then enough to clear line of water.
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source and 3. Locate a 1" to 11D?" (1.25 cm to 3.18 cm) vertical cold water
reset the control (Thermostat, Refrigerator or Freezer Control pipe near the refrigerator.
depending on the model) to the desired setting.IMPORTANT:
Make sure it is a cold water pipe.
Water Supply RequirementsHorizontal pipe will work, but drill on the top side of the
Read all directions carefully before you begin.pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
IMPORTANT:
If you turn the refrigerator on before the water line is 4. Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the
connected, turn the ice maker OFF.water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1D?"
All installations must meet local plumbing code requirements.(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both
Use copper tubing and check for leaks. Install copper tubing ends of copper tubing are cut square.
only in areas where the household temperatures will remain 5. Using a grounded drill, drill a 1D?" hole in the cold water pipe
above freezing.you have selected.
TOOLS NEEDED: Flat-blade screwdriver, wD??" and 1D?" open-end A
wrenches or two adjustable wrenches, 1D?" nut driver and drill bit, B
hand drill or electric drill (properly grounded).G
NOTE: Your refrigerator dealer has a kit available with a 1D?" C
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3D??"
(4.76 mm) saddle valve which reduces water flow and clogs more F ED
easily.A.Cold water pipeE.Compression sleeve
B.Pipe clampF.Shutoff valve
C.Copper tubingG.Packing nut
D.Compression nut
4 |
ACEC
WHIRLPOOL
